Small Low Profile Ceiling Fans – The flush-style ceiling fan is mounted snugly alongside a flat horizontal fairly low ceiling where it really is off the beaten track, and where it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, with regards to the size of the room being fitted, and will cost typically from $30 to $300. It generally has three fan motor speeds, which are reversible. Except for the tools and possible other regions necessary for installing them, their self-assemble kits include everything else. In many cases, the fan, that can have its lighting, will replace a ceiling light fixture.
Safety, The electricity must be off once your there in which the fan will be installed. If the fan is replacing a light fixture, de-activate its fuse or circuit breaker along with flipping its wall switch to the off position. Stand on a sturdy wide-berth step stool or ladder during the installation; tend not to lean or get into a twisted position while there. Also, wear protective eyeglasses or goggles. Furthermore, if additional auxiliary household wiring is necessary, get professional advice or help first. Tools needed, instructions (electrical) eyeglasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and further screws for securing the junction box, as appropriate
Installation steps (seeing the fan installation instructions thoroughly). 1. Remove the light fixture from the ceiling. With the electricity off, slowly eliminate the shade, bulbs, and fixture screws from the electrical junction box inside ceiling. Let the skeleton fixture hang there. With the light tester, ensure the wire connections for this fixture are cold (test light will stay off). Cut the wires, leaving 3-5″ of tail allowing you to connect these to the ceiling fan motor assembly. If the residence is old, only two wires might exist, a black one as well as a white one. Tip: also check the firmness in the electrical box inside ceiling. If it really is not solidly connected to the ceiling, add two extra screws to its top side, which could require drilling two holes inside box for the children. The ceiling fan is heavier compared to the light fixture. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends in the tailing wires inside junction box cleanly, install the mounting bracket for the box with the two 5/32″ screw-bolts provided. Let the tailing wires hang outside in the bracket. 3. Hang the motor assembly from the bracket. Insert the topside motor-hanger in the centralized holder in the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly should really swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one for your motor as well as a blue or off-color one for your lights to get attached below it. Overlap the stripped ends of those two wires (motor and lights) together with the stripped end in the black ceiling wire inside box, and twist connect them together with the wire nut provided. Connect the white assembly wire for the white ceiling wire much the same way.
Then, to hold these connections from loosening whilst the fan is working, tape the wide lower ends of those nuts for their wires with electrical tape. Also, attach the green fan wire (ground wire from the bracket frame) for the electrical box in the event the box can be grounded having a third bare or green wire. Otherwise, in the event the electrical box in not grounded, ask an experienced about this green wire connection. Some will say to leave it be, i.e., do nothing by using it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud for the far ends in the mounting bracket with the small screws provided. It covers/hides the perimeters in the motor and the wiring and ceiling box. 6. Assemble the fan blades (3 to 5) and mount them. After picking out the top or bottom reversible blade color scheme preferred, attach the blades for their end brackets with the screws and washers provided. Then mount the blades for the bottom side of fan motor with the bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed for the motor to hold them separate from the rest in the kit hardware.
Tip: to hold the motor from becoming too off-level during this step, install the blades one-by-one opposite together first of all. 7. Install the lighting assembly. Attach the fan’s lighting assembly for the small round central housing unit just below the fan blades through quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders inside order instructed. Note: a housing cap is provided in the event the lighting assembly is just not wanted without any reason. 8. Test the fan and lights. After turning the electricity back on, flip the wall switch to on. Set the pull-chain switches as desired. Often, the fan lighting is set in the future on with the wall switch, whilst the fan itself is controlled by the pull-chain switch only, initially set inside off position. Note: The ceiling fan includes a reversible motor switch that enables the draft either to go upward or downward as preferred. For more information on ceiling fan installation, start to see the following sites.