Lone Star Ceiling Fan

Posted on

Hampton Bay Al875 Bk Lonestar Ii Indoor Natural Iron Ceiling Fan inside sizing 1000 X 1000Hampton Bay Al875 Bk Lonestar Ii Indoor Natural Iron Ceiling Fan inside sizing 1000 X 1000


Lone Star Ceiling Fan – The flush-style ceiling fan is mounted snugly next to a set horizontal fairly low ceiling where it is off the beaten track, and from where it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, according to the size of the room being fitted, and may cost typically from $30 to $300. It generally has three fan motor speeds, that are reversible. Except for the tools and possible other areas necessary for installing them, their self-assemble kits come with the rest. In many cases, the fan, that will have its own lighting, will replace a ceiling fitting.

Safety, The electricity must be off once your there the place that the fan is usually to be installed. If the fan is replacing a fitting, power down its fuse or circuit breaker together with flipping its wall switch to the off position. Stand on a sturdy wide-berth step stool or ladder throughout the installation; tend not to lean or enter a twisted position while there. Also, wear protective eye-glasses or goggles. Furthermore, if additional auxiliary household wiring is required, get professional advice or help first. Tools needed, instructions (electrical) eye-glasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and additional screws for securing the junction box, if needed

Installation steps (looking at the fan installation instructions thoroughly). 1. Remove the fitting from the ceiling. With the electricity off, slowly get rid of the shade, bulbs, and fixture screws from the electrical junction box within the ceiling. Let the skeleton fixture hang there. With the light tester, make sure the wire connections to the fixture are cold (the test light will always be off). Cut the wires, leaving 3-5″ of tail for connecting these phones the ceiling fan motor assembly. If the residence is old, only two wires might exist, a black one plus a white one. Tip: also look into the firmness with the electrical box within the ceiling. If it is not solidly coupled to the ceiling, add two extra screws to its top side, which can require drilling two holes within the box for the children. The ceiling fan is heavier than the fitting. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends with the tailing wires within the junction box cleanly, install the mounting bracket for the box with all the two 5/32″ screw-bolts provided. Let the tailing wires hang outside with the bracket. 3. Hang the motor assembly from the bracket. Insert the topside motor-hanger in the centralized holder with the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly should really swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one for that motor plus a blue or off-color one for that lights to get attached below it. Overlap the stripped ends of such two wires (motor and lights) together with all the stripped end with the black ceiling wire within the box, and twist connect them together with all the wire nut provided. Connect the white assembly wire for the white ceiling wire exactly the same way.


Then, to maintain these connections from loosening whilst the fan is working, tape the wide lower ends of such nuts on their wires with electrical tape. Also, attach the green fan wire (ground wire from the bracket frame) for the electrical box if the box can be grounded having a third bare or green wire. Otherwise, if the electrical box in not grounded, ask a professional relating to this green wire connection. Some will say to get forced out be, i.e., do nothing with it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud for the far ends with the mounting bracket with all the small screws provided. It covers/hides the sides with the motor along with the wiring and ceiling box. 6. Assemble the fan blades (4 to 6) and mount them. After deciding on the top or bottom reversible blade color scheme preferred, attach the blades on their end brackets with all the screws and washers provided. Then mount the blades for the bottom side of fan motor with all the bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed for the motor to maintain them separate from the rest with the kit hardware.

Tip: to maintain the motor from becoming too off-level within this step, install the blades one by one opposite together to begin with. 7. Install the lighting assembly. Attach the fan’s lighting assembly for the small round central housing unit just underneath the fan blades through quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders within the order instructed. Note: a housing cap is provided if the lighting assembly is not wanted at all. 8. Test the fan and lights. After turning the electricity back on, flip the wall switch to on. Set the pull-chain switches as desired. Often, the fan lighting is set to come on with all the wall switch, whilst the fan itself is controlled with the pull-chain switch only, initially set within the off position. Note: The ceiling fan features a reversible motor switch that enables the draft either to go upward or downward as preferred. For more information on ceiling fan installation, begin to see the following sites.