Flush Mount Outdoor Ceiling Fans – The flush-style ceiling fan is mounted snugly alongside a set horizontal fairly low ceiling where it is taken care of, and from where it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, with regards to the room size being fitted, and may cost typically from $30 to $300. It generally has three fan motor speeds, that happen to be reversible. Except for the instruments and possible other regions essential for installing them, their self-assemble kits have the rest. In many cases, the fan, that will have its lighting, will replace a ceiling fitting.
Safety, The electricity has to be off to begin where the fan shall be installed. If the fan is replacing a fitting, de-activate its fuse or circuit breaker as well as flipping its wall switch the signal from the off position. Stand on a sturdy wide-berth step stool or ladder in the installation; tend not to lean or get into a twisted position while there. Also, wear protective eye glasses or goggles. Furthermore, if additional auxiliary household wiring is necessary, get professional advice or help first. Tools needed, instructions (electrical) eye glasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and extra screws for securing the junction box, if required
Installation steps (after reading the fan installation instructions thoroughly). 1. Remove the fitting in the ceiling. With the electricity off, slowly take away the shade, bulbs, and fixture screws in the electrical junction box inside the ceiling. Let the skeleton fixture hang there. With the light tester, guarantee the wire connections to this particular fixture are cold (test light will stay off). Cut the wires, leaving 3-5″ of tail to get in touch these to the ceiling fan motor assembly. If the home is old, only two wires might exist, a black one plus a white one. Tip: also look into the firmness with the electrical box inside the ceiling. If it is not solidly attached to the ceiling, add two extra screws to its top side, which could require drilling two holes inside the box for them. The ceiling fan is heavier compared to the fitting. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends with the tailing wires inside the junction box cleanly, install the mounting bracket for the box using the two 5/32″ screw-bolts provided. Let the tailing wires hang outside with the bracket. 3. Hang the motor assembly in the bracket. Insert the topside motor-hanger to the centralized holder with the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly should really swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one to the motor plus a blue or off-color one to the lights to become attached below it. Overlap the stripped ends of these two wires (motor and lights) together using the stripped end with the black ceiling wire inside the box, and twist connect them together using the wire nut provided. Connect the white assembly wire for the white ceiling wire much the same way.
Then, to help keep these connections from loosening as the fan is working, tape the wide lower ends of these nuts for their wires with electrical tape. Also, attach the green fan wire (ground wire in the bracket frame) for the electrical box when the box can be grounded having a third bare or green wire. Otherwise, when the electrical box in not grounded, ask an experienced about it green wire connection. Some will say to get forced out be, i.e., do nothing at all by it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud for the far ends with the mounting bracket using the small screws provided. It covers/hides the edges with the motor along with the wiring and ceiling box. 6. Assemble the fan blades (3 to 5) and mount them. After seeking the top or bottom reversible blade color scheme preferred, attach the blades for their end brackets using the screws and washers provided. Then mount the blades for the bottom side of fan motor using the bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed for the motor to help keep them separate in the rest with the kit hardware.
Tip: to help keep the motor from becoming too off-level within this step, install the blades one-by-one opposite to each other to begin with. 7. Install the lighting assembly. Attach the fan’s lighting assembly for the small round central housing unit just underneath the fan blades via the quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders inside the order instructed. Note: a housing cap is provided when the lighting assembly just isn’t wanted unconditionally. 8. Test the fan and lights. After turning the electricity back on, flip the wall switch the signal from on. Set the pull-chain switches as desired. Often, the fan lighting is set into the future on using the wall switch, as the fan itself is controlled with the pull-chain switch only, initially set inside the off position. Note: The ceiling fan has a reversible motor switch that allows the draft either to go upward or downward as preferred. For more information on ceiling fan installation, start to see the following sites.