Ceiling Fans With Lights Flush Mount – Two top reasons to purchase a ceiling fan, air conditioning. If you live in a very cold climate, fans can push warm air gathered at the ceiling back off. Ceiling fans might be easy to install in case you have some mechanical aptitude. Current ceiling fans come with remote-controls to vary speed and adjust lighting. If your room already includes a fitting in the ceiling, your fitting probably has one hot or feed wire going to it, the neutral white along with the bonding green or copper. Essentially this can be a three-wire system. Many new construction homes have four wires available, one to the light the other to the fan motor control along with the neutral and ground. If you just have one Hot wire feeding the ceiling junction box, the remote-control fans work together with your application. Additionally some remote-controlled fans use wall controller which sends its signal to the fan being a TV remote. It just appears to be a wall control unit. If you only need the electricity wire for the remote-controlled fan, please cap off of the fourth wire which you will not want to use. This should be shown within your directions that included the fan assembly.
Once you have acquired a follower you want, build it according to the instructions given. Some fans really are a extra complex, ask a pal to aid if required. It is best to make sure it is assembled correctly, developing a ceiling fan blade thud you on the head might be annoying. Once you have the pre-assembly completed, now you can prepare the ceiling junction box. Of course I know you have already made certain the electricity to the ceiling box is deterred with out one can possibly energize it accidentally. Once you have done this, you should find three wires in the J-box. A copper or green wire for bonding. A white wire to the neutral along with a red or black wire to the power. If your junction box includes a fourth wire, this would be set up for a wall controlled fan switch which can be great and allows you to use a non-remote wall controller. I should mention that some all fans come with a wall controllers designed as remotes so do not be confused because they all assist the singular feed within your ceiling junction box.
A word about weight, not yours but anything concerning the size of your fan. If you have a substantial fan and its weighted near 12 pounds or maybe more, you need a special junction box that will support the excess weight. I would recommend you ask someone that knows about these heavier fans if that’s what you will be going to install. Most fans are lighter and might be installed in most junction boxes without modifications.
Now why don’t we get up there, the fan that is. Many fans come with a Hanger in the shape of a U. Install this hanger onto your box, the screws should be 8/32 types. That means a size 8 diameter or gauge screw with 32 threads per inch. Once you have the hanger installed, pick-up your fan motor minus the blades installed and hang up it around the hanger. This allows you the electrician to get together the wires without struggling to juggle the motor and wire it concurrently. Connect the bonding wire to the chassis as noted in the instructions. Next connect the white neutral wire, now the black wire. Swing the fan into place while using parts provided. Some have brackets, some make use of a metal plate although some use preformed mounting bases. Use your instructions and you will have a follower in no time. Smaller fans may require you to pre-assemble your blades before hanging the fan. I always found installing the motor first and after that installing the blades last is much easier. It does require however, you to work above your mind to obtain the blades attached.
Once you have the fan hanging, the blades installed and everything tightened now you can step off of the ladder, relax, then install the wall controller as provided. These all vary in design nevertheless they all follow similar procedures. Remember, you will have a line and load situation here. This means, the queue side will be the pair of wires the feed in the switch box through the panel while the Load side is going to your fan. This is critical so make sure you see the difference. Connect the Load side first: Connect your bonding wire first. Then connect your white neutral wire. Then your hot wire. Next perform the Line (incoming) side next: Bond or ground should already be composed to the new controller. Next wire your white neutral to the controllers neutral to the Line side. You may have already wired your neutrals together as outlined by your instructions. Now wire your Hot or Power wire to the Line side of your controller. If you have the fourth wire in that room, cap them back or use it to the motor control and connect it accordingly to your directions. Red to Red is often the case here. Once completed, make yourself some Iced Tea and luxuriate in your fan.