52 Inch White Ceiling Fan – The flush-style ceiling fan is mounted snugly beside a set horizontal fairly low ceiling where it is taken care of, and from which it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, with regards to the size of the room being fitted, and may cost typically from $30 to $300. It generally has three fan motor speeds, which are reversible. Except for the instruments and possible other areas required for installing them, their self-assemble kits come with anything else. In many cases, the fan, which will have a unique lighting, will replace a ceiling permanent fixture.
Safety, The electricity has to be off at the site the location where the fan will be installed. If the fan is replacing a permanent fixture, shut down its fuse or circuit breaker in addition to flipping its wall switch to the off position. Stand on a sturdy wide-berth step stool or ladder throughout the installation; don’t lean or end up in a twisted position while there. Also, wear protective eyeglasses or goggles. Furthermore, if additional auxiliary household wiring is needed, get professional advice or help first. Tools needed, instructions (electrical) eyeglasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and extra screws for securing the junction box, if needed
Installation steps (seeing the fan installation instructions thoroughly). 1. Remove the permanent fixture from your ceiling. With the electricity off, slowly get rid of the shade, bulbs, and fixture screws from your electrical junction box within the ceiling. Let the skeleton fixture hang there. With the light tester, make sure the wire connections for this fixture are cold (the exam light will always be off). Cut the wires, leaving 3-5″ of tail allowing you to connect them to the ceiling fan motor assembly. If the residence is old, only two wires might exist, a black one plus a white one. Tip: also check the firmness from the electrical box within the ceiling. If it is not solidly coupled to the ceiling, add two extra screws to its top side, which might require drilling two holes within the box for them. The ceiling fan is heavier than the permanent fixture. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends from the tailing wires within the junction box cleanly, install the mounting bracket towards the box with all the two 5/32″ screw-bolts provided. Let the tailing wires hang outside from the bracket. 3. Hang the motor assembly from your bracket. Insert the topside motor-hanger to the centralized holder from the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly should really swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one to the motor plus a blue or off-color one to the lights being attached below it. Overlap the stripped ends of such two wires (motor and lights) together with all the stripped end from the black ceiling wire within the box, and twist connect them together with all the wire nut provided. Connect the white assembly wire towards the white ceiling wire the same way.
Then, to help keep these connections from loosening as the fan is working, tape the wide lower ends of such nuts for their wires with electrical tape. Also, attach the green fan wire (ground wire from your bracket frame) towards the electrical box in the event the box is also grounded with a third bare or green wire. Otherwise, in the event the electrical box in not grounded, ask a professional about it green wire connection. Some will say to let it rest be, i.e., do nothing at all by using it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud towards the far ends from the mounting bracket with all the small screws provided. It covers/hides the perimeters from the motor along with the wiring and ceiling box. 6. Assemble the fan blades (3 to 5) and mount them. After seeking the top or bottom reversible blade color scheme preferred, attach the blades for their end brackets with all the screws and washers provided. Then mount the blades towards the bottom side of fan motor with all the bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed towards the motor to help keep them separate from your rest from the kit hardware.
Tip: to help keep the motor from becoming too off-level within this step, install the blades one-by-one opposite together to start with. 7. Install the lighting assembly. Attach the fan’s lighting assembly towards the small round central housing unit just beneath the fan blades via the quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders within the order instructed. Note: a housing cap is provided in the event the lighting assembly is not wanted unconditionally. 8. Test the fan and lights. After turning the electricity back on, flip the wall switch to on. Set the pull-chain switches as desired. Often, the fan lighting is set ahead on with all the wall switch, as the fan itself is controlled with the pull-chain switch only, initially set within the off position. Note: The ceiling fan carries a reversible motor switch that permits the draft either to go upward or downward as preferred. For more information on ceiling fan installation, start to see the following sites.