Rustic Ceiling Fans – The flush-style ceiling fan is mounted snugly next to a set horizontal fairly low ceiling where it’s taken care of, and from which it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, with regards to the room size being fitted, and may cost typically from $30 to $300. It generally has three fan motor speeds, that are reversible. Except for the instruments and possible other areas necessary for installing them, their self-assemble kits feature the rest. In many cases, the fan, that will have its very own lighting, will replace a ceiling light fixture.
Safety, The electricity should be off to begin in which the fan is usually to be installed. If the fan is replacing a light fixture, power down its fuse or circuit breaker in addition to flipping its wall switch to the off position. Stand on a sturdy wide-berth step stool or ladder through the installation; usually do not lean or enter a twisted position while there. Also, wear protective eyeglasses or goggles. Furthermore, if additional auxiliary household wiring is necessary, get professional advice or help first. Tools needed, instructions (electrical) eyeglasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and further screws for securing the junction box, if needed
Installation steps (seeing the fan installation instructions thoroughly). 1. Remove the light fixture from the ceiling. With the electricity off, slowly get rid of the shade, bulbs, and fixture screws from the electrical junction box in the ceiling. Let the skeleton fixture hang there. With the light tester, ensure that the wire connections to the fixture are cold (the exam light will stay off). Cut the wires, leaving 3-5″ of tail to get in touch these phones the ceiling fan motor assembly. If the property is old, only two wires might exist, a black one along with a white one. Tip: also check the firmness from the electrical box in the ceiling. If it’s not solidly coupled to the ceiling, add two extra screws to its top side, that might require drilling two holes in the box for the kids. The ceiling fan is heavier than the light fixture. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends from the tailing wires in the junction box cleanly, install the mounting bracket on the box with the two 5/32″ screw-bolts provided. Let the tailing wires hang outside from the bracket. 3. Hang the motor assembly from the bracket. Insert the topside motor-hanger in the centralized holder from the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly really should swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one for the motor along with a blue or off-color one for the lights to get attached below it. Overlap the stripped ends of these two wires (motor and lights) together with the stripped end from the black ceiling wire in the box, and twist connect them together with the wire nut provided. Connect the white assembly wire on the white ceiling wire exactly the same.
Then, to maintain these connections from loosening even though the fan is working, tape the wide lower ends of these nuts for their wires with electrical tape. Also, attach the green fan wire (ground wire from the bracket frame) on the electrical box when the box is also grounded with a third bare or green wire. Otherwise, when the electrical box in not grounded, ask an expert about this green wire connection. Some will say to let it rest be, i.e., do nothing at all from it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud on the far ends from the mounting bracket with the small screws provided. It covers/hides the perimeters from the motor and also the wiring and ceiling box. 6. Assemble the fan blades (3 to 4) and mount them. After seeking the top or bottom reversible blade color scheme preferred, attach the blades for their end brackets with the screws and washers provided. Then mount the blades on the bottom side of fan motor with the bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed on the motor to maintain them separate from the rest from the kit hardware.
Tip: to maintain the motor from becoming too off-level during this step, install the blades one at a time opposite to each other to begin with. 7. Install the lighting assembly. Attach the fan’s lighting assembly on the small round central housing unit just under the fan blades through the quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders in the order instructed. Note: a housing cap is provided when the lighting assembly is not wanted at all. 8. Test the fan and lights. After turning the electricity back on, flip the wall switch to on. Set the pull-chain switches as desired. Often, the fan lighting is set in the future on with the wall switch, even though the fan itself is controlled by the pull-chain switch only, initially set in the off position. Note: The ceiling fan carries a reversible motor switch that permits the draft either to go upward or downward as preferred. For more information on ceiling fan installation, see the following sites.