Stained Glass Ceiling Fan – The flush-style ceiling fan is mounted snugly next to a flat horizontal fairly low ceiling where it is out of the way, and from which it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, with respect to the size of the room being fitted, and may cost typically from $30 to $300. It generally has three fan motor speeds, which can be reversible. Except for the equipment and possible other parts required for installing them, their self-assemble kits have any devices. In many cases, the fan, which will have its own lighting, will replace a ceiling fitting.
Safety, The electricity must be off to begin the place that the fan will be installed. If the fan is replacing a fitting, power down its fuse or circuit breaker together with flipping its wall change to the off position. Stand on a sturdy wide-berth step stool or ladder throughout the installation; tend not to lean or get into a twisted position while there. Also, wear protective eyeglasses or goggles. Furthermore, if additional auxiliary household wiring is necessary, get professional advice or help first. Tools needed, instructions (electrical) eyeglasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and extra screws for securing the junction box, if required
Installation steps (seeing the fan installation instructions thoroughly). 1. Remove the fitting from the ceiling. With the electricity off, slowly eliminate the shade, bulbs, and fixture screws from the electrical junction box inside ceiling. Let the skeleton fixture hang there. With the light tester, make sure the wire connections to this fixture are cold (test light will always be off). Cut the wires, leaving 3-5″ of tail to get in touch these phones the ceiling fan motor assembly. If the property is old, only two wires might exist, a black one as well as a white one. Tip: also check the firmness from the electrical box inside ceiling. If it is not solidly coupled to the ceiling, add two extra screws to its top side, that might require drilling two holes inside box for them. The ceiling fan is heavier than the fitting. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends from the tailing wires inside junction box cleanly, install the mounting bracket on the box while using two 5/32″ screw-bolts provided. Let the tailing wires hang outside from the bracket. 3. Hang the motor assembly from the bracket. Insert the topside motor-hanger in to the centralized holder from the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly really should swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one for your motor as well as a blue or off-color one for your lights to get attached below it. Overlap the stripped ends of these two wires (motor and lights) together while using stripped end from the black ceiling wire inside box, and twist connect them together while using wire nut provided. Connect the white assembly wire on the white ceiling wire much the same way.
Then, to hold these connections from loosening even though the fan is working, tape the wide lower ends of these nuts for their wires with electrical tape. Also, attach the green fan wire (ground wire from the bracket frame) on the electrical box if the box is also grounded with a third bare or green wire. Otherwise, if the electrical box in not grounded, ask a professional about it green wire connection. Some will say to get forced out be, i.e., do nothing by it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud on the far ends from the mounting bracket while using small screws provided. It covers/hides the edges from the motor along with the wiring and ceiling box. 6. Assemble the fan blades (3 to 4) and mount them. After seeking the top or bottom reversible blade color scheme preferred, attach the blades for their end brackets while using screws and washers provided. Then mount the blades on the bottom side of fan motor while using bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed on the motor to hold them separate from the rest from the kit hardware.
Tip: to hold the motor from becoming too off-level in this step, install the blades one-by-one opposite to each other first of all. 7. Install the lighting assembly. Attach the fan’s lighting assembly on the small round central housing unit just underneath the fan blades through the quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders inside order instructed. Note: a housing cap is provided if the lighting assembly is just not wanted without any reason. 8. Test the fan and lights. After turning the electricity back on, flip the wall change to on. Set the pull-chain switches as desired. Often, the fan lighting is set in the future on while using wall switch, even though the fan itself is controlled with the pull-chain switch only, initially set inside off position. Note: The ceiling fan has a reversible motor switch that permits the draft either to go upward or downward as preferred. For more information on ceiling fan installation, start to see the following sites.