Ceiling Fan For Vaulted Ceiling – Two good reasons to purchase a ceiling fan, air conditioning. If you live inside a cold climate, fans can push warm air gathered nearby the ceiling back. Ceiling fans can be simple to install when you have some mechanical aptitude. Current ceiling fans include remote-controls to vary speed and adjust lighting. If your room already has a permanent fixture in the ceiling, your permanent fixture probably has one hot or feed wire likely to it, the neutral white along with the bonding green or copper. Essentially this is a three-wire system. Many new construction homes have four wires available, one for your light the other for your fan motor control along with the neutral and ground. If you have only one Hot wire feeding the ceiling junction box, the remote-control fans will work along with your application. Additionally some remote-controlled fans use wall controller which sends its signal to the fan just like a TV remote. It just seems like a wall control unit. If you just have the electricity wire to your remote-controlled fan, please cap from the fourth wire which you will not require to use. This must be shown inside your directions that was included with the fan assembly.
Once you have acquired an admirer you like, build it according to the instructions given. Some fans certainly are a little more complex, ask a buddy to help you if you need to. It is best to makes it assembled correctly, having a ceiling fan blade thud your self on the head can be annoying. Once you have the pre-assembly completed, now you can prepare the ceiling junction box. Of course I know you have already made certain the electricity to the ceiling box is deterred no you can energize it accidentally. Once you have carried this out, you must find three wires in the J-box. A copper or green wire for bonding. A white wire for your neutral as well as a red or black wire for your power. If your junction box has a fourth wire, this would be set up for the wall controlled fan switch that’s great and allows you to use a non-remote wall controller. I should mention that some all fans include a wall controllers designed as remotes so you shouldn’t be confused because these all help the singular feed inside your ceiling junction box.
A word about weight, not yours but a word in regards to the sized your fan. If you have a sizable fan and its weighted near 12 pounds or higher, you will need a special junction box that will offer the excess weight. I would recommend i hear you ask someone that knows about these heavier fans you might need what you really are likely to install. Most fans are lighter and can be positioned in most junction boxes without modifications.
Now we should get it down there, the fan which is. Many fans include a Hanger the same shape as a U. Install this hanger on your box, the screws must be 8/32 types. That means a size 8 diameter or gauge screw with 32 threads per inch. Once you have the hanger installed, get your fan motor without the blades installed and hang up it around the hanger. This allows you the electrician to connect the wires without struggling to juggle the motor and wire it simultaneously. Connect the bonding wire to the chassis as noted in the instructions. Next connect the white neutral wire, and now the black wire. Swing the fan into place using the parts provided. Some have brackets, some utilize a metal plate while some use preformed mounting bases. Use your instructions and you will have an admirer quickly. Smaller fans may require that you pre-assemble your blades before hanging the fan. I always found installing the motor first after which installing the blades last is much easier. It does require however, that you work above your mind to find the blades attached.
Once you have the fan hanging, the blades installed and everything tightened now you can step from the ladder, relax, then install the wall controller as provided. These all vary in design but they all follow similar procedures. Remember, you will have line and load situation here. This means, the road side could be the group of wires the feed in the switch box through the panel as the Load side is likely to your fan. This is critical so be sure to comprehend the difference. Connect the Load side first: Connect your bonding wire first. Then connect your white neutral wire. Then your hot wire. Next do the Line (incoming) side next: Bond or ground should already be composed to the new controller. Next wire your white neutral to the controllers neutral for your Line side. You may have already wired your neutrals together in accordance with your instructions. Now wire your Hot or Power wire to the Line side of your controller. If you have the fourth wire within, cap rid of it or use it for your motor control and connect it accordingly in your directions. Red to Red is usually the case here. Once completed, make yourself some Iced Tea and luxuriate in a new fan.