Rattan Ceiling Fans – The flush-style ceiling fan is mounted snugly next to a set horizontal fairly low ceiling where it’s dealt with, and where it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, with regards to the room size being fitted, and can cost typically from $30 to $300. It generally has three fan motor speeds, which are reversible. Except for the tools and possible the rest required for installing them, their self-assemble kits have everything else. In many cases, the fan, that can have its very own lighting, will replace a ceiling light fixture.
Safety, The electricity have to be off once your there the location where the fan is usually to be installed. If the fan is replacing a light fixture, turn off its fuse or circuit breaker as well as flipping its wall exchange signal of the off position. Stand on a sturdy wide-berth step stool or ladder in the installation; tend not to lean or enter a twisted position while there. Also, wear protective eye glasses or goggles. Furthermore, if additional auxiliary household wiring is required, get professional advice or help first. Tools needed, instructions (electrical) eye glasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and additional screws for securing the junction box, if necessary
Installation steps (looking at the fan installation instructions thoroughly). 1. Remove the light fixture through the ceiling. With the electricity off, slowly take away the shade, bulbs, and fixture screws through the electrical junction box in the ceiling. Let the skeleton fixture hang there. With the light tester, ensure the wire connections to this fixture are cold (the exam light will remain off). Cut the wires, leaving 3-5″ of tail for connecting these to the ceiling fan motor assembly. If the home is old, only two wires might exist, a black one along with a white one. Tip: also look into the firmness of the electrical box in the ceiling. If it’s not solidly attached to the ceiling, add two extra screws to its top side, which can require drilling two holes in the box for them. The ceiling fan is heavier as opposed to light fixture. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends of the tailing wires in the junction box cleanly, install the mounting bracket for the box while using two 5/32″ screw-bolts provided. Let the tailing wires hang outside of the bracket. 3. Hang the motor assembly through the bracket. Insert the topside motor-hanger to the centralized holder of the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly should certainly swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one for your motor along with a blue or off-color one for your lights being attached below it. Overlap the stripped ends of such two wires (motor and lights) together while using stripped end of the black ceiling wire in the box, and twist connect them together while using wire nut provided. Connect the white assembly wire for the white ceiling wire exactly the same way.
Then, to help keep these connections from loosening whilst the fan is working, tape the wide lower ends of such nuts on their wires with electrical tape. Also, attach the green fan wire (ground wire through the bracket frame) for the electrical box in the event the box is additionally grounded having a third bare or green wire. Otherwise, in the event the electrical box in not grounded, ask a specialist relating to this green wire connection. Some will say to let it sit be, i.e., relax by using it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud for the far ends of the mounting bracket while using small screws provided. It covers/hides the perimeters of the motor and also the wiring and ceiling box. 6. Assemble the fan blades (3 to 4) and mount them. After deciding on the top or bottom reversible blade color scheme preferred, attach the blades on their end brackets while using screws and washers provided. Then mount the blades for the bottom side of fan motor while using bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed for the motor to help keep them separate through the rest of the kit hardware.
Tip: to help keep the motor from becoming too off-level in this step, install the blades one by one opposite together in the first place. 7. Install the lighting assembly. Attach the fan’s lighting assembly for the small round central housing unit just below the fan blades through the quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders in the order instructed. Note: a housing cap is provided in the event the lighting assembly is just not wanted at all. 8. Test the fan and lights. After turning the electricity back on, flip the wall exchange signal of on. Set the pull-chain switches as desired. Often, the fan lighting is set to come on while using wall switch, whilst the fan itself is controlled with the pull-chain switch only, initially set in the off position. Note: The ceiling fan features a reversible motor switch that allows the draft either to go upward or downward as preferred. For more information on ceiling fan installation, begin to see the following sites.