Ceiling Fan Control Switch – Two top reasons to put in a ceiling fan, air conditioning. If you live inside a cold climate, fans can push heated air gathered at the ceiling down again. Ceiling fans may be easy to install in case you have some mechanical aptitude. Current ceiling fans include remote-controls to vary speed and adjust lighting. If your room already carries a light fixture inside the ceiling, your light fixture probably has one hot or feed wire going to it, the neutral white and the bonding green or copper. Essentially this can be a three-wire system. Many new construction homes have four wires available, one for the light and one for the fan motor control and the neutral and ground. If you just have one Hot wire feeding the ceiling junction box, the remote-control fans will continue to work using your application. Additionally some remote-controlled fans use wall controller which sends its signal for the fan just like a TV remote. It just looks like a wall control unit. If you merely have the electricity wire on your remote-controlled fan, please cap over fourth wire which you will n’t need to use. This ought to be shown inside your directions that was included with the fan assembly.
Once you’ve got acquired a lover you want, assemble it according for the instructions given. Some fans certainly are a extra complex, ask a friend to help you if necessary. It is best to make sure it is assembled correctly, using a ceiling fan blade thud yourself the top may be annoying. Once you’ve got the pre-assembly completed, anyone can prepare the ceiling junction box. Of course I know you’ve got already made certain the electricity for the ceiling box is switched off no it’s possible to energize it accidentally. Once you’ve got done this, you need to find three wires inside the J-box. A copper or green wire for bonding. A white wire for the neutral plus a red or black wire for the power. If your junction box carries a fourth wire, this would be setup for any wall controlled fan switch which is great and allows you to use a non-remote wall controller. I should mention that some all fans include a wall controllers designed as remotes so don’t be confused because these all work with the singular feed inside your ceiling junction box.
A word about weight, not yours but a thing regarding the height and width of your fan. If you’ve got a large fan and its particular weighted near 12 pounds or even more, you may need a special junction box that can secure the additional weight. I would recommend you ask somebody that knows about these heavier fans if that’s what you really are going to install. Most fans are lighter and may be positioned in most junction boxes without modifications.
Now why don’t we get it there, the fan which is. Many fans include a Hanger shaped like a U. Install this hanger onto your box, the screws ought to be 8/32 types. That means a size 8 diameter or gauge screw with 32 threads per inch. Once you’ve got the hanger installed, pick up your fan motor without the blades installed and it for the hanger. This allows you the electrician to connect the wires without struggling to juggle the motor and wire it as well. Connect the bonding wire for the chassis as noted inside the instructions. Next connect the white neutral wire, and now the black wire. Swing the fan into place while using parts provided. Some have brackets, some utilize a metal plate although some use preformed mounting bases. Use your instructions you’ll also find a lover very quickly. Smaller fans may need you to definitely pre-assemble your blades before hanging the fan. I always found installing the motor first then installing the blades last is much simpler. It does require however, you to definitely work above your mind to obtain the blades attached.
Once you’ve got the fan hanging, the blades installed and everything tightened anyone can step over ladder, take a deep breath, then install the wall controller as provided. These all vary in design nevertheless they all follow similar procedures. Remember, you will find a line and load situation here. This means, the road side could be the group of wires the feed into the switch box through the panel whilst the Load side is going to your fan. This is critical so ensure you view the difference. Connect the Load side first: Connect your bonding wire first. Then connect your white neutral wire. Then your hot wire. Next perform Line (incoming) side next: Bond or ground should already be comprised for the new controller. Next wire your white neutral for the controllers neutral for the Line side. You may have already wired your neutrals together as outlined by your instructions. Now wire your Hot or Power wire for the Line side of your controller. If you’ve got the fourth wire inside, cap it well or use it for the motor control and connect it accordingly in your directions. Red to Red is usually the case here. Once completed, get yourself some Iced Tea and enjoy your brand-new fan.