Low Profile Ceiling Fans – The flush-style ceiling fan is mounted snugly close to a set horizontal fairly low ceiling where it really is dealt with, and where it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, with respect to the size of room being fitted, and may cost typically from $30 to $300. It generally has three fan motor speeds, that happen to be reversible. Except for the equipment and possible the rest essential for installing them, their self-assemble kits feature everything else. In many cases, the fan, which will have its very own lighting, will replace a ceiling fitting.
Safety, The electricity must be off once your there in which the fan is to be installed. If the fan is replacing a fitting, power down its fuse or circuit breaker together with flipping its wall switch to the off position. Stand on a sturdy wide-berth step stool or ladder through the installation; don’t lean or enter a twisted position while there. Also, wear protective eyeglasses or goggles. Furthermore, if additional auxiliary household wiring is necessary, get professional advice or help first. Tools needed, instructions (electrical) eyeglasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and additional screws for securing the junction box, if needed
Installation steps (after reading the fan installation instructions thoroughly). 1. Remove the fitting through the ceiling. With the electricity off, slowly remove the shade, bulbs, and fixture screws through the electrical junction box inside ceiling. Let the skeleton fixture hang there. With the light tester, ensure the wire connections to the fixture are cold (the exam light will continue to be off). Cut the wires, leaving 3-5″ of tail allowing you to connect the crooks to the ceiling fan motor assembly. If the house is old, only two wires might exist, a black one along with a white one. Tip: also look at the firmness from the electrical box inside ceiling. If it really is not solidly connected to the ceiling, add two extra screws to its top side, which might require drilling two holes inside box for the children. The ceiling fan is heavier compared to the fitting. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends from the tailing wires inside junction box cleanly, install the mounting bracket to the box using the two 5/32″ screw-bolts provided. Let the tailing wires hang outside from the bracket. 3. Hang the motor assembly through the bracket. Insert the topside motor-hanger to the centralized holder from the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly should certainly swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one for the motor along with a blue or off-color one for the lights to get attached below it. Overlap the stripped ends of the two wires (motor and lights) together using the stripped end from the black ceiling wire inside box, and twist connect them together using the wire nut provided. Connect the white assembly wire to the white ceiling wire much the same way.
Then, to help keep these connections from loosening as the fan is working, tape the wide lower ends of the nuts for their wires with electrical tape. Also, attach the green fan wire (ground wire through the bracket frame) to the electrical box if your box is additionally grounded using a third bare or green wire. Otherwise, if your electrical box in not grounded, ask a specialist about this green wire connection. Some will say to let it rest be, i.e., do nothing from it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud to the far ends from the mounting bracket using the small screws provided. It covers/hides the perimeters from the motor along with the wiring and ceiling box. 6. Assemble the fan blades (4 to 6) and mount them. After picking out the top or bottom reversible blade color scheme preferred, attach the blades for their end brackets using the screws and washers provided. Then mount the blades to the bottom side of fan motor using the bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed to the motor to help keep them separate through the rest from the kit hardware.
Tip: to help keep the motor from becoming too off-level during this step, install the blades one-by-one opposite to each other to begin with. 7. Install the lighting assembly. Attach the fan’s lighting assembly to the small round central housing unit just below the fan blades through the quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders inside order instructed. Note: a housing cap is provided if your lighting assembly isn’t wanted at all. 8. Test the fan and lights. After turning the electricity back on, flip the wall switch to on. Set the pull-chain switches as desired. Often, the fan lighting is set ahead on using the wall switch, as the fan itself is controlled from the pull-chain switch only, initially set inside off position. Note: The ceiling fan includes a reversible motor switch that enables the draft either to go upward or downward as preferred. For more information on ceiling fan installation, understand the following sites.