Wicker Ceiling Fan Blades – Two reasons to install a ceiling fan, heating and cooling. If you live in a very cold climate, fans can push heated air gathered close to the ceiling down again. Ceiling fans can be all to easy to install when you have some mechanical aptitude. Current ceiling fans have remote-controls to vary speed and adjust lighting. If your room already features a permanent fixture inside the ceiling, your permanent fixture probably has one hot or feed wire likely to it, the neutral white along with the bonding green or copper. Essentially this is the three-wire system. Many new construction homes have four wires available, one for your light and one for your fan motor control along with the neutral and ground. If you have only one Hot wire feeding the ceiling junction box, the remote-control fans will continue to work along with your application. Additionally some remote-controlled fans use wall controller which sends its signal towards the fan just like a TV remote. It just appears to be a wall control unit. If you only need the electricity wire on your remote-controlled fan, please cap off the fourth wire which you will n’t need to make use of. This should be shown in your directions that included the fan assembly.
Once you have acquired a follower that suits you, put it together according towards the instructions given. Some fans certainly are a much more complex, ask a friend to assist if you need to. It is best to make sure it is assembled correctly, developing a ceiling fan blade thud your self on the head can be annoying. Once you have the pre-assembly completed, it’s simple to prepare the ceiling junction box. Of course I know you have already ensured the electricity towards the ceiling box is switched off with out one can energize it accidentally. Once you have succeeded in doing so, you should find three wires inside the J-box. A copper or green wire for bonding. A white wire for your neutral and a red or black wire for your power. If your junction box features a fourth wire, this may be setup for a wall controlled fan switch which can be great and allows you to make use of a non-remote wall controller. I should mention that some all fans have a wall controllers designed as remotes so you shouldn’t be confused as these all work with the singular feed in your ceiling junction box.
A word about weight, not yours but a thing about the size your fan. If you have a big fan as well as weighted near 12 pounds or more, you may need a special junction box that may support the excess weight. I would recommend you may ask somebody who knows about these heavier fans you might need what you really are likely to install. Most fans are lighter and can be set up in most junction boxes without modifications.
Now we should get up there, the fan which is. Many fans have a Hanger shaped like a U. Install this hanger onto your box, the screws should be 8/32 types. That means a size 8 diameter or gauge screw with 32 threads per inch. Once you have the hanger installed, pick-up your fan motor without the blades installed and hang up it on the hanger. This allows you the electrician to get together the wires without struggling to juggle the motor and wire it as well. Connect the bonding wire towards the chassis as noted inside the instructions. Next connect the white neutral wire, and now the black wire. Swing the fan into place with all the parts provided. Some have brackets, some make use of a metal plate while others use preformed mounting bases. Use your instructions you’ll also find a follower quickly. Smaller fans may need you to pre-assemble your blades before hanging the fan. I always found installing the motor first then installing the blades last is much easier. It does require however, you to work above your face to have the blades attached.
Once you have the fan hanging, the blades installed and everything tightened it’s simple to step off the ladder, relax, then install the wall controller as provided. These all vary in design however they all follow similar procedures. Remember, you’ll have a line and load situation here. This means, the road side could be the set of wires the feed into the switch box from the panel whilst the Load side is likely to your fan. This is critical so be sure you see the difference. Connect the Load side first: Connect your bonding wire first. Then connect your white neutral wire. Then your hot wire. Next perform Line (incoming) side next: Bond or ground should already be constructed towards the new controller. Next wire your white neutral towards the controllers neutral for your Line side. You may have already wired your neutrals together as outlined by your instructions. Now wire your Hot or Power wire towards the Line side of your controller. If you have the fourth wire in there, cap rid of it or use it for your motor control and connect it accordingly to your directions. Red to Red is truly the case here. Once completed, get yourself some Iced Tea and luxuriate in your new fan.