Hampton Bay Florentine Iv 56 In Indoor Brushed Nickel Ceiling Fan within dimensions 1000 X 1000Clear Blade Ceiling Fan – The flush-style ceiling fan is mounted snugly beside a flat horizontal fairly low ceiling where it can be taken care of, and from which it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, with respect to the size of the room being fitted, and may cost typically from $30 to $300. It generally has three fan motor speeds, which can be reversible. Except for the tools and possible other areas essential for installing them, their self-assemble kits come with the rest. In many cases, the fan, which will have its lighting, will replace a ceiling permanent fixture.
Safety, The electricity has to be off once your there the location where the fan shall be installed. If the fan is replacing a permanent fixture, turn off its fuse or circuit breaker together with flipping its wall switch to the off position. Stand on a sturdy wide-berth step stool or ladder throughout the installation; don’t lean or enter into a twisted position while there. Also, wear protective eye glasses or goggles. Furthermore, if additional auxiliary household wiring should be used, get professional advice or help first. Tools needed, instructions (electrical) eye glasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and extra screws for securing the junction box, if required
Installation steps (seeing the fan installation instructions thoroughly). 1. Remove the permanent fixture in the ceiling. With the electricity off, slowly remove the shade, bulbs, and fixture screws in the electrical junction box in the ceiling. Let the skeleton fixture hang there. With the light tester, make sure the wire connections for this fixture are cold (the test light will always be off). Cut the wires, leaving 3-5″ of tail for connecting them to the ceiling fan motor assembly. If the home is old, only two wires might exist, a black one as well as a white one. Tip: also check the firmness in the electrical box in the ceiling. If it can be not solidly coupled to the ceiling, add two extra screws to its top side, which can require drilling two holes in the box on their behalf. The ceiling fan is heavier compared to permanent fixture. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends in the tailing wires in the junction box cleanly, install the mounting bracket towards the box while using two 5/32″ screw-bolts provided. Let the tailing wires hang outside in the bracket. 3. Hang the motor assembly in the bracket. Insert the topside motor-hanger into the centralized holder in the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly should certainly swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one to the motor as well as a blue or off-color one to the lights to become attached below it. Overlap the stripped ends of these two wires (motor and lights) together while using stripped end in the black ceiling wire in the box, and twist connect them together while using wire nut provided. Connect the white assembly wire towards the white ceiling wire the same way.
Then, to hold these connections from loosening as the fan is working, tape the wide lower ends of these nuts on their wires with electrical tape. Also, attach the green fan wire (ground wire in the bracket frame) towards the electrical box if your box can be grounded using a third bare or green wire. Otherwise, if your electrical box in not grounded, ask an expert about it green wire connection. Some will say to get forced out be, i.e., do nothing at all by using it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud towards the far ends in the mounting bracket while using small screws provided. It covers/hides the perimeters in the motor and the wiring and ceiling box. 6. Assemble the fan blades (four to six) and mount them. After seeking the top or bottom reversible blade color scheme preferred, attach the blades on their end brackets while using screws and washers provided. Then mount the blades towards the bottom side of fan motor while using bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed towards the motor to hold them separate in the rest in the kit hardware.
Tip: to hold the motor from becoming too off-level during this step, install the blades one at a time opposite to each other first of all. 7. Install the lighting assembly. Attach the fan’s lighting assembly towards the small round central housing unit just below the fan blades through quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders in the order instructed. Note: a housing cap is provided if your lighting assembly isn’t wanted unconditionally. 8. Test the fan and lights. After turning the electricity back on, flip the wall switch to on. Set the pull-chain switches as desired. Often, the fan lighting is set to come on while using wall switch, as the fan itself is controlled through the pull-chain switch only, initially set in the off position. Note: The ceiling fan features a reversible motor switch that allows the draft either to go upward or downward as preferred. For more information on ceiling fan installation, see the following sites.
