Orient Style 60 Inch 40 Watt Bldc Giant Solar Ceiling Fan With Light throughout size 1000 X 793Solar Ceiling Fan – The flush-style ceiling fan is mounted snugly next to a set horizontal fairly low ceiling where it’s out of the way, and from which it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, according to the size of the room being fitted, and may cost typically from $30 to $300. It generally has three fan motor speeds, that are reversible. Except for the instruments and possible the rest required for installing them, their self-assemble kits come with the rest. In many cases, the fan, that may have its lighting, will replace a ceiling fitting.
Safety, The electricity have to be off at the site the place that the fan will be installed. If the fan is replacing a fitting, shut down its fuse or circuit breaker as well as flipping its wall change to the off position. Stand on a sturdy wide-berth step stool or ladder during the installation; do not lean or end up in a twisted position while there. Also, wear protective eye glasses or goggles. Furthermore, if additional auxiliary household wiring is required, get professional advice or help first. Tools needed, instructions (electrical) eye glasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and extra screws for securing the junction box, if necessary
Installation steps (looking at the fan installation instructions thoroughly). 1. Remove the fitting from your ceiling. With the electricity off, slowly eliminate the shade, bulbs, and fixture screws from your electrical junction box inside the ceiling. Let the skeleton fixture hang there. With the light tester, ensure the wire connections for this fixture are cold (the exam light will continue to be off). Cut the wires, leaving 3-5″ of tail to get in touch these phones the ceiling fan motor assembly. If the property is old, only two wires might exist, a black one as well as a white one. Tip: also look into the firmness of the electrical box inside the ceiling. If it’s not solidly coupled to the ceiling, add two extra screws to its top side, which might require drilling two holes inside the box for the children. The ceiling fan is heavier compared to the fitting. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends of the tailing wires inside the junction box cleanly, install the mounting bracket towards the box with all the two 5/32″ screw-bolts provided. Let the tailing wires hang outside of the bracket. 3. Hang the motor assembly from your bracket. Insert the topside motor-hanger into the centralized holder of the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly should really swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one for that motor as well as a blue or off-color one for that lights to become attached below it. Overlap the stripped ends of the two wires (motor and lights) together with all the stripped end of the black ceiling wire inside the box, and twist connect them together with all the wire nut provided. Connect the white assembly wire towards the white ceiling wire exactly the same way.
Then, to help keep these connections from loosening whilst the fan is working, tape the wide lower ends of the nuts with their wires with electrical tape. Also, attach the green fan wire (ground wire from your bracket frame) towards the electrical box in the event the box is additionally grounded with a third bare or green wire. Otherwise, in the event the electrical box in not grounded, ask a professional concerning this green wire connection. Some will say to let it sit be, i.e., relax by it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud towards the far ends of the mounting bracket with all the small screws provided. It covers/hides the sides of the motor as well as the wiring and ceiling box. 6. Assemble the fan blades (3 to 5) and mount them. After deciding on the top or bottom reversible blade color scheme preferred, attach the blades with their end brackets with all the screws and washers provided. Then mount the blades towards the bottom side of fan motor with all the bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed towards the motor to help keep them separate from your rest of the kit hardware.
Tip: to help keep the motor from becoming too off-level during this step, install the blades one-by-one opposite together to begin with. 7. Install the lighting assembly. Attach the fan’s lighting assembly towards the small round central housing unit just underneath the fan blades using the quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders inside the order instructed. Note: a housing cap is provided in the event the lighting assembly is not wanted for any reason. 8. Test the fan and lights. After turning the electricity back on, flip the wall change to on. Set the pull-chain switches as desired. Often, the fan lighting is set to come on with all the wall switch, whilst the fan itself is controlled with the pull-chain switch only, initially set inside the off position. Note: The ceiling fan has a reversible motor switch that enables the draft either to go upward or downward as preferred. For more information on ceiling fan installation, see the following sites.
