Pacific Ceiling Fans – Two top reasons to purchase a ceiling fan, air conditioning. If you live in a cold climate, fans can push heated air gathered close to the ceiling back down. Ceiling fans may be easy to install in case you have some mechanical aptitude. Current ceiling fans come with remote-controls to vary speed and adjust lighting. If your room already includes a light fixture inside the ceiling, your light fixture probably has one hot or feed wire gonna it, the neutral white along with the bonding green or copper. Essentially this is the three-wire system. Many new construction homes have four wires available, one to the light the other to the fan motor control along with the neutral and ground. If you have only one Hot wire feeding the ceiling junction box, the remote-control fans work with your application. Additionally some remote-controlled fans use wall controller which sends its signal to the fan just like a TV remote. It just looks like a wall control unit. If you really need the ability wire for the remote-controlled fan, please cap off the fourth wire which you will not need to utilize. This needs to be shown in your directions that came with the fan assembly.
Once you’ve got acquired an admirer you want, build it according to the instructions given. Some fans are a extra complex, ask a pal to assist if need be. It is best to make sure it is assembled correctly, developing a ceiling fan blade thud your self on your head may be annoying. Once you’ve got the pre-assembly completed, it’s simple to prepare the ceiling junction box. Of course I know you’ve got already made certain the ability to the ceiling box is powered down and no you can energize it accidentally. Once you’ve got succeeded in doing so, you need to find three wires inside the J-box. A copper or green wire for bonding. A white wire to the neutral plus a red or black wire to the power. If your junction box includes a fourth wire, this would be build for the wall controlled fan switch that is great and allows you to utilize a non-remote wall controller. I should mention that some all fans come with a wall controllers designed as remotes so avoid being confused as these all work with the singular feed in your ceiling junction box.
A word about weight, not yours but a thing about the size of your fan. If you’ve got a large fan and its particular weighted near 12 pounds or even more, you may need a special junction box that will support the extra body fat. I would recommend you ask someone who knows about these heavier fans recommendations what you will be gonna install. Most fans are lighter and may be positioned in most junction boxes without modifications.
Now why don’t we get it there, the fan which is. Many fans come with a Hanger shaped like a U. Install this hanger on to your box, the screws needs to be 8/32 types. That means a size 8 diameter or gauge screw with 32 threads per inch. Once you’ve got the hanger installed, pick up your fan motor without the blades installed and hang it about the hanger. This allows you the electrician to hook up the wires without struggling to juggle the motor and wire it at the same time. Connect the bonding wire to the chassis as noted inside the instructions. Next connect the white neutral wire, now the black wire. Swing the fan into place while using parts provided. Some have brackets, some use a metal plate and some use preformed mounting bases. Use your instructions you’ll also find an admirer very quickly. Smaller fans may necessitate one to pre-assemble your blades before hanging the fan. I always found installing the motor first then installing the blades last is easier. It does require however, one to work above your head to have the blades attached.
Once you’ve got the fan hanging, the blades installed and everything tightened it’s simple to step off the ladder, take a deep breath, then install the wall controller as provided. These all vary in design but they all follow similar procedures. Remember, you will have line and load situation here. This means, the road side is the pair of wires the feed into the switch box from the panel while the Load side is gonna your fan. This is critical so be sure to see the difference. Connect the Load side first: Connect your bonding wire first. Then connect your white neutral wire. Then your hot wire. Next perform the Line (incoming) side next: Bond or ground should already be constructed to the new controller. Next wire your white neutral to the controllers neutral to the Line side. You may have already wired your neutrals together according to your instructions. Now wire your Hot or Power wire to the Line side of the controller. If you’ve got the fourth wire in that room, cap rid of it or use it to the motor control and connect it accordingly in your directions. Red to Red is truly the case here. Once completed, be some Iced Tea and enjoy a new fan.