Ceiling Fan Light Shade – The flush-style ceiling fan is mounted snugly alongside a set horizontal fairly low ceiling where it really is taken care of, and where it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, with regards to the size of the room being fitted, which enable it to cost typically from $30 to $300. It generally has three fan motor speeds, that are reversible. Except for the various tools and possible the rest required for installing them, their self-assemble kits have anything else. In many cases, the fan, that can have its own lighting, will replace a ceiling fitting.
Safety, The electricity must be off to begin the location where the fan is to be installed. If the fan is replacing a fitting, turn off its fuse or circuit breaker in addition to flipping its wall change to the off position. Stand on a sturdy wide-berth step stool or ladder during the installation; usually do not lean or end up in a twisted position while there. Also, wear protective eye glasses or goggles. Furthermore, if additional auxiliary household wiring is needed, get professional advice or help first. Tools needed, instructions (electrical) eye glasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and additional screws for securing the junction box, if necessary
Installation steps (looking at the fan installation instructions thoroughly). 1. Remove the fitting through the ceiling. With the electricity off, slowly get rid of the shade, bulbs, and fixture screws through the electrical junction box inside ceiling. Let the skeleton fixture hang there. With the light tester, ensure the wire connections for this fixture are cold (quality light will remain off). Cut the wires, leaving 3-5″ of tail in order to connect these phones the ceiling fan motor assembly. If the residence is old, only two wires might exist, a black one as well as a white one. Tip: also confirm the firmness of the electrical box inside ceiling. If it really is not solidly connected to the ceiling, add two extra screws to its top side, which might require drilling two holes inside box for the kids. The ceiling fan is heavier compared to the fitting. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends of the tailing wires inside junction box cleanly, install the mounting bracket towards the box with the two 5/32″ screw-bolts provided. Let the tailing wires hang outside of the bracket. 3. Hang the motor assembly through the bracket. Insert the topside motor-hanger to the centralized holder of the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly should certainly swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one for the motor as well as a blue or off-color one for the lights to get attached below it. Overlap the stripped ends of these two wires (motor and lights) together with the stripped end of the black ceiling wire inside box, and twist connect them together with the wire nut provided. Connect the white assembly wire towards the white ceiling wire exactly the same.
Then, to hold these connections from loosening as the fan is working, tape the wide lower ends of these nuts to their wires with electrical tape. Also, attach the green fan wire (ground wire through the bracket frame) towards the electrical box when the box can also be grounded using a third bare or green wire. Otherwise, when the electrical box in not grounded, ask an expert relating to this green wire connection. Some will say to let it sit be, i.e., relax from it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud towards the far ends of the mounting bracket with the small screws provided. It covers/hides the edges of the motor and the wiring and ceiling box. 6. Assemble the fan blades (four to six) and mount them. After picking out the top or bottom reversible blade color scheme preferred, attach the blades to their end brackets with the screws and washers provided. Then mount the blades towards the bottom side of fan motor with the bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed towards the motor to hold them separate through the rest of the kit hardware.
Tip: to hold the motor from becoming too off-level during this step, install the blades one at a time opposite to one another to begin with. 7. Install the lighting assembly. Attach the fan’s lighting assembly towards the small round central housing unit just underneath the fan blades through the quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders inside order instructed. Note: a housing cap is provided when the lighting assembly is just not wanted unconditionally. 8. Test the fan and lights. After turning the electricity back on, flip the wall change to on. Set the pull-chain switches as desired. Often, the fan lighting is set into the future on with the wall switch, as the fan itself is controlled by the pull-chain switch only, initially set inside off position. Note: The ceiling fan carries a reversible motor switch that permits the draft either to go upward or downward as preferred. For more information on ceiling fan installation, begin to see the following sites.