Kitchen Exhaust Fans Ceiling Mount – The flush-style ceiling fan is mounted snugly beside a set horizontal fairly low ceiling where it’s out of the way, and from where it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, with respect to the room size being fitted, and can cost typically from $30 to $300. It generally has three fan motor speeds, that are reversible. Except for the equipment and possible other areas necessary for installing them, their self-assemble kits feature the rest. In many cases, the fan, that may have its very own lighting, will replace a ceiling permanent fixture.
Safety, The electricity have to be off at the site the location where the fan is usually to be installed. If the fan is replacing a permanent fixture, power down its fuse or circuit breaker in addition to flipping its wall change to the off position. Stand on a sturdy wide-berth step stool or ladder throughout the installation; tend not to lean or enter a twisted position while there. Also, wear protective eye glasses or goggles. Furthermore, if additional auxiliary household wiring should be used, get professional advice or help first. Tools needed, instructions (electrical) eye glasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and further screws for securing the junction box, if needed
Installation steps (looking at the fan installation instructions thoroughly). 1. Remove the permanent fixture in the ceiling. With the electricity off, slowly remove the shade, bulbs, and fixture screws in the electrical junction box inside the ceiling. Let the skeleton fixture hang there. With the light tester, guarantee the wire connections for this fixture are cold (quality light will always be off). Cut the wires, leaving 3-5″ of tail in order to connect these to the ceiling fan motor assembly. If the home is old, only two wires might exist, a black one and a white one. Tip: also look into the firmness in the electrical box inside the ceiling. If it’s not solidly attached to the ceiling, add two extra screws to its top side, which could require drilling two holes inside the box for the kids. The ceiling fan is heavier as opposed to permanent fixture. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends in the tailing wires inside the junction box cleanly, install the mounting bracket on the box using the two 5/32″ screw-bolts provided. Let the tailing wires hang outside in the bracket. 3. Hang the motor assembly in the bracket. Insert the topside motor-hanger to the centralized holder in the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly really should swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one for that motor and a blue or off-color one for that lights to get attached below it. Overlap the stripped ends of these two wires (motor and lights) together using the stripped end in the black ceiling wire inside the box, and twist connect them together using the wire nut provided. Connect the white assembly wire on the white ceiling wire exactly the same way.
Then, to maintain these connections from loosening as the fan is working, tape the wide lower ends of these nuts to their wires with electrical tape. Also, attach the green fan wire (ground wire in the bracket frame) on the electrical box in the event the box is additionally grounded which has a third bare or green wire. Otherwise, in the event the electrical box in not grounded, ask an experienced about this green wire connection. Some will say to let it sit be, i.e., do nothing at all by using it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud on the far ends in the mounting bracket using the small screws provided. It covers/hides the edges in the motor and the wiring and ceiling box. 6. Assemble the fan blades (4 to 6) and mount them. After choosing the top or bottom reversible blade color scheme preferred, attach the blades to their end brackets using the screws and washers provided. Then mount the blades on the bottom side of fan motor using the bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed on the motor to maintain them separate in the rest in the kit hardware.
Tip: to maintain the motor from becoming too off-level in this step, install the blades one at a time opposite to one another to start with. 7. Install the lighting assembly. Attach the fan’s lighting assembly on the small round central housing unit just below the fan blades via the quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders inside the order instructed. Note: a housing cap is provided in the event the lighting assembly is just not wanted for any reason. 8. Test the fan and lights. After turning the electricity back on, flip the wall change to on. Set the pull-chain switches as desired. Often, the fan lighting is set to come on using the wall switch, as the fan itself is controlled by the pull-chain switch only, initially set inside the off position. Note: The ceiling fan features a reversible motor switch that enables the draft either to go upward or downward as preferred. For more information on ceiling fan installation, start to see the following sites.