Small Outdoor Ceiling Fan With Light – The flush-style ceiling fan is mounted snugly close to a flat horizontal fairly low ceiling where it really is taken care of, and where it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, depending on the room size being fitted, and may cost typically from $30 to $300. It generally has three fan motor speeds, that happen to be reversible. Except for the various tools and possible other regions essential for installing them, their self-assemble kits feature the rest. In many cases, the fan, which will have a unique lighting, will replace a ceiling permanent fixture.
Safety, The electricity must be off to begin where the fan will be installed. If the fan is replacing a permanent fixture, shut down its fuse or circuit breaker together with flipping its wall switch to the off position. Stand on a sturdy wide-berth step stool or ladder through the installation; do not lean or enter into a twisted position while there. Also, wear protective eyeglasses or goggles. Furthermore, if additional auxiliary household wiring is needed, get professional advice or help first. Tools needed, instructions (electrical) eyeglasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and further screws for securing the junction box, if needed
Installation steps (seeing the fan installation instructions thoroughly). 1. Remove the permanent fixture from your ceiling. With the electricity off, slowly take away the shade, bulbs, and fixture screws from your electrical junction box in the ceiling. Let the skeleton fixture hang there. With the light tester, make sure the wire connections for this fixture are cold (the exam light will remain off). Cut the wires, leaving 3-5″ of tail for connecting the crooks to the ceiling fan motor assembly. If the house is old, only two wires might exist, a black one and a white one. Tip: also confirm the firmness in the electrical box in the ceiling. If it really is not solidly connected to the ceiling, add two extra screws to its top side, which can require drilling two holes in the box for the children. The ceiling fan is heavier compared to the permanent fixture. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends in the tailing wires in the junction box cleanly, install the mounting bracket towards the box with the two 5/32″ screw-bolts provided. Let the tailing wires hang outside in the bracket. 3. Hang the motor assembly from your bracket. Insert the topside motor-hanger in the centralized holder in the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly should really swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one to the motor and a blue or off-color one to the lights to be attached below it. Overlap the stripped ends of these two wires (motor and lights) together with the stripped end in the black ceiling wire in the box, and twist connect them together with the wire nut provided. Connect the white assembly wire towards the white ceiling wire the same way.
Then, to maintain these connections from loosening as the fan is working, tape the wide lower ends of these nuts to their wires with electrical tape. Also, attach the green fan wire (ground wire from your bracket frame) towards the electrical box if the box is also grounded which has a third bare or green wire. Otherwise, if the electrical box in not grounded, ask an experienced relating to this green wire connection. Some will say to leave it be, i.e., do nothing from it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud towards the far ends in the mounting bracket with the small screws provided. It covers/hides the edges in the motor as well as the wiring and ceiling box. 6. Assemble the fan blades (3 to 5) and mount them. After deciding on the top or bottom reversible blade color scheme preferred, attach the blades to their end brackets with the screws and washers provided. Then mount the blades towards the bottom side of fan motor with the bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed towards the motor to maintain them separate from your rest in the kit hardware.
Tip: to maintain the motor from becoming too off-level within this step, install the blades one at a time opposite to each other first of all. 7. Install the lighting assembly. Attach the fan’s lighting assembly towards the small round central housing unit just underneath the fan blades using the quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders in the order instructed. Note: a housing cap is provided if the lighting assembly is just not wanted for any reason. 8. Test the fan and lights. After turning the electricity back on, flip the wall switch to on. Set the pull-chain switches as desired. Often, the fan lighting is set to come on with the wall switch, as the fan itself is controlled with the pull-chain switch only, initially set in the off position. Note: The ceiling fan has a reversible motor switch that enables the draft either to go upward or downward as preferred. For more information on ceiling fan installation, start to see the following sites.