Mission Ceiling Fan With Light Quorum 53524 86 in dimensions 1500 X 952Mission Ceiling Fan – The flush-style ceiling fan is mounted snugly next to a flat horizontal fairly low ceiling where it really is dealt with, and where it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, with respect to the room size being fitted, and will cost typically from $30 to $300. It generally has three fan motor speeds, that happen to be reversible. Except for the various tools and possible other areas required for installing them, their self-assemble kits feature anything else. In many cases, the fan, that will have its very own lighting, will replace a ceiling fitting.
Safety, The electricity have to be off once your there in which the fan is to be installed. If the fan is replacing a fitting, shut down its fuse or circuit breaker in addition to flipping its wall switch the signal from the off position. Stand on a sturdy wide-berth step stool or ladder during the installation; usually do not lean or enter a twisted position while there. Also, wear protective eye glasses or goggles. Furthermore, if additional auxiliary household wiring should be used, get professional advice or help first. Tools needed, instructions (electrical) eye glasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and additional screws for securing the junction box, as appropriate
Installation steps (seeing the fan installation instructions thoroughly). 1. Remove the fitting from your ceiling. With the electricity off, slowly take away the shade, bulbs, and fixture screws from your electrical junction box inside the ceiling. Let the skeleton fixture hang there. With the light tester, make sure the wire connections to this particular fixture are cold (test light will always be off). Cut the wires, leaving 3-5″ of tail in order to connect them to the ceiling fan motor assembly. If the home is old, only two wires might exist, a black one plus a white one. Tip: also confirm the firmness from the electrical box inside the ceiling. If it really is not solidly attached to the ceiling, add two extra screws to its top side, that might require drilling two holes inside the box for them. The ceiling fan is heavier than the fitting. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends from the tailing wires inside the junction box cleanly, install the mounting bracket to the box using the two 5/32″ screw-bolts provided. Let the tailing wires hang outside from the bracket. 3. Hang the motor assembly from your bracket. Insert the topside motor-hanger into the centralized holder from the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly is supposed to swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one for that motor plus a blue or off-color one for that lights to get attached below it. Overlap the stripped ends of those two wires (motor and lights) together using the stripped end from the black ceiling wire inside the box, and twist connect them together using the wire nut provided. Connect the white assembly wire to the white ceiling wire exactly the same.
Then, to maintain these connections from loosening even though the fan is working, tape the wide lower ends of those nuts on their wires with electrical tape. Also, attach the green fan wire (ground wire from your bracket frame) to the electrical box if your box can also be grounded which has a third bare or green wire. Otherwise, if your electrical box in not grounded, ask a specialist about it green wire connection. Some will say to let it rest be, i.e., do nothing at all from it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud to the far ends from the mounting bracket using the small screws provided. It covers/hides the perimeters from the motor and the wiring and ceiling box. 6. Assemble the fan blades (four to six) and mount them. After choosing the top or bottom reversible blade color scheme preferred, attach the blades on their end brackets using the screws and washers provided. Then mount the blades to the bottom side of fan motor using the bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed to the motor to maintain them separate from your rest from the kit hardware.
Tip: to maintain the motor from becoming too off-level in this step, install the blades one at a time opposite together in the first place. 7. Install the lighting assembly. Attach the fan’s lighting assembly to the small round central housing unit just below the fan blades via the quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders inside the order instructed. Note: a housing cap is provided if your lighting assembly is just not wanted unconditionally. 8. Test the fan and lights. After turning the electricity back on, flip the wall switch the signal from on. Set the pull-chain switches as desired. Often, the fan lighting is set to come on using the wall switch, even though the fan itself is controlled by the pull-chain switch only, initially set inside the off position. Note: The ceiling fan includes a reversible motor switch which allows the draft either to go upward or downward as preferred. For more information on ceiling fan installation, start to see the following sites.
