Hunter Channing 60 In Led Indoor Brushed Nickel Ceiling Fan With inside sizing 1000 X 100060 Inch Ceiling Fan With Light – The flush-style ceiling fan is mounted snugly beside a designated horizontal fairly low ceiling where it really is off the beaten track, and where it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, according to the size of the room being fitted, and may cost typically from $30 to $300. It generally has three fan motor speeds, that are reversible. Except for the equipment and possible other areas essential for installing them, their self-assemble kits come with any devices. In many cases, the fan, that can have a unique lighting, will replace a ceiling permanent fixture.
Safety, The electricity has to be off once your there the place that the fan is to be installed. If the fan is replacing a permanent fixture, turn off its fuse or circuit breaker as well as flipping its wall switch to the off position. Stand on a sturdy wide-berth step stool or ladder in the installation; usually do not lean or enter into a twisted position while there. Also, wear protective eyeglasses or goggles. Furthermore, if additional auxiliary household wiring is necessary, get professional advice or help first. Tools needed, instructions (electrical) eyeglasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and further screws for securing the junction box, if required
Installation steps (looking at the fan installation instructions thoroughly). 1. Remove the permanent fixture from your ceiling. With the electricity off, slowly remove the shade, bulbs, and fixture screws from your electrical junction box inside the ceiling. Let the skeleton fixture hang there. With the light tester, make sure the wire connections to this particular fixture are cold (the exam light will remain off). Cut the wires, leaving 3-5″ of tail allowing you to connect the crooks to the ceiling fan motor assembly. If the residence is old, only two wires might exist, a black one along with a white one. Tip: also check the firmness with the electrical box inside the ceiling. If it really is not solidly coupled to the ceiling, add two extra screws to its top side, which might require drilling two holes inside the box for the kids. The ceiling fan is heavier compared to the permanent fixture. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends with the tailing wires inside the junction box cleanly, install the mounting bracket to the box with all the two 5/32″ screw-bolts provided. Let the tailing wires hang outside with the bracket. 3. Hang the motor assembly from your bracket. Insert the topside motor-hanger in the centralized holder with the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly should really swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one for that motor along with a blue or off-color one for that lights to get attached below it. Overlap the stripped ends of those two wires (motor and lights) together with all the stripped end with the black ceiling wire inside the box, and twist connect them together with all the wire nut provided. Connect the white assembly wire to the white ceiling wire exactly the same.
Then, to keep these connections from loosening whilst the fan is working, tape the wide lower ends of those nuts with their wires with electrical tape. Also, attach the green fan wire (ground wire from your bracket frame) to the electrical box if your box can also be grounded having a third bare or green wire. Otherwise, if your electrical box in not grounded, ask a specialist relating to this green wire connection. Some will say to get forced out be, i.e., relax by using it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud to the far ends with the mounting bracket with all the small screws provided. It covers/hides the sides with the motor and the wiring and ceiling box. 6. Assemble the fan blades (3 to 4) and mount them. After choosing the top or bottom reversible blade color scheme preferred, attach the blades with their end brackets with all the screws and washers provided. Then mount the blades to the bottom side of fan motor with all the bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed to the motor to keep them separate from your rest with the kit hardware.
Tip: to keep the motor from becoming too off-level within this step, install the blades one at a time opposite to each other in the first place. 7. Install the lighting assembly. Attach the fan’s lighting assembly to the small round central housing unit just under the fan blades via the quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders inside the order instructed. Note: a housing cap is provided if your lighting assembly isn’t wanted without any reason. 8. Test the fan and lights. After turning the electricity back on, flip the wall switch to on. Set the pull-chain switches as desired. Often, the fan lighting is set to come on with all the wall switch, whilst the fan itself is controlled by the pull-chain switch only, initially set inside the off position. Note: The ceiling fan includes a reversible motor switch which allows the draft either to go upward or downward as preferred. For more information on ceiling fan installation, begin to see the following sites.
