Ceiling Fan Pole – The flush-style ceiling fan is mounted snugly alongside a set horizontal fairly low ceiling where it really is dealt with, and from where it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, with respect to the room size being fitted, and will cost typically from $30 to $300. It generally has three fan motor speeds, that are reversible. Except for the tools and possible other areas necessary for installing them, their self-assemble kits feature any devices. In many cases, the fan, that may have a unique lighting, will replace a ceiling permanent fixture.
Safety, The electricity has to be off at the site where the fan is usually to be installed. If the fan is replacing a permanent fixture, shut down its fuse or circuit breaker along with flipping its wall exchange signal of the off position. Stand on a sturdy wide-berth step stool or ladder in the installation; usually do not lean or enter into a twisted position while there. Also, wear protective eyeglasses or goggles. Furthermore, if additional auxiliary household wiring should be used, get professional advice or help first. Tools needed, instructions (electrical) eyeglasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and extra screws for securing the junction box, if necessary
Installation steps (after reading the fan installation instructions thoroughly). 1. Remove the permanent fixture from your ceiling. With the electricity off, slowly eliminate the shade, bulbs, and fixture screws from your electrical junction box inside ceiling. Let the skeleton fixture hang there. With the light tester, ensure that the wire connections to this particular fixture are cold (the test light will remain off). Cut the wires, leaving 3-5″ of tail allowing you to connect them to the ceiling fan motor assembly. If the residence is old, only two wires might exist, a black one as well as a white one. Tip: also check the firmness in the electrical box inside ceiling. If it really is not solidly coupled to the ceiling, add two extra screws to its top side, which could require drilling two holes inside box for the kids. The ceiling fan is heavier compared to permanent fixture. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends in the tailing wires inside junction box cleanly, install the mounting bracket on the box while using two 5/32″ screw-bolts provided. Let the tailing wires hang outside in the bracket. 3. Hang the motor assembly from your bracket. Insert the topside motor-hanger in the centralized holder in the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly is supposed to swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one for the motor as well as a blue or off-color one for the lights being attached below it. Overlap the stripped ends of these two wires (motor and lights) together while using stripped end in the black ceiling wire inside box, and twist connect them together while using wire nut provided. Connect the white assembly wire on the white ceiling wire exactly the same.
Then, to keep these connections from loosening as the fan is working, tape the wide lower ends of these nuts with their wires with electrical tape. Also, attach the green fan wire (ground wire from your bracket frame) on the electrical box when the box can be grounded which has a third bare or green wire. Otherwise, when the electrical box in not grounded, ask a professional relating to this green wire connection. Some will say to let it sit be, i.e., do nothing by using it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud on the far ends in the mounting bracket while using small screws provided. It covers/hides the perimeters in the motor and also the wiring and ceiling box. 6. Assemble the fan blades (3 to 5) and mount them. After seeking the top or bottom reversible blade color scheme preferred, attach the blades with their end brackets while using screws and washers provided. Then mount the blades on the bottom side of fan motor while using bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed on the motor to keep them separate from your rest in the kit hardware.
Tip: to keep the motor from becoming too off-level in this step, install the blades one-by-one opposite together to start with. 7. Install the lighting assembly. Attach the fan’s lighting assembly on the small round central housing unit just beneath the fan blades using the quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders inside order instructed. Note: a housing cap is provided when the lighting assembly is just not wanted without any reason. 8. Test the fan and lights. After turning the electricity back on, flip the wall exchange signal of on. Set the pull-chain switches as desired. Often, the fan lighting is set ahead on while using wall switch, as the fan itself is controlled from the pull-chain switch only, initially set inside off position. Note: The ceiling fan features a reversible motor switch that permits the draft either to go upward or downward as preferred. For more information on ceiling fan installation, understand the following sites.