Thompson Deck Stain – Why don’t we begin first we need to look at the area could it be a turf or concrete base underneath the decking a turf base will have to be dug off and membrane put underneath the decking it is possible to and should put membrane under any decking project to prevent any weeds penetrating through, where would be the damp course levels once we don’t need the deck above the damp course ideally the deck ought to be two bricks below the damp course. And will there be any drain access points underneath the decking since these need a unique decking drain cover. Always remember the decking boards go horizontal along the home. Always remember decking higher that 1.2m from the walk-out need planning permission
Now we have assessed these factors they’ll decide the height of the deck and then for any special requirements that have to be incorporated to the decking project. Estimation of materials first measure the area from the decking i.e 4.8m x 4.8m = 23.04sq meters. Then use this equation to calculate the decking boards needed 4800mm / 140mm (deck board width which can be 4.8m long) = 35 decking boards. Add a little for cuts and edges that have to be filled in. Then calculate the burden bearing supports (4 x 2 pressure treated CLS) 4800 / 600 = 8 This the volume of horizontal 4 x 2 pieces needed for your internal structure from the decking plus the outside from the frame i.e. 4800 x 4 = 19.2m + (8 x 4800) = 58m of four x 2. Add some for your cross member struts and positioning pegs (banged and concreted if needed to the ground) about a few 4.8m lengths should suffice.
Setting up the frame this should be done near or as close on the position from the final deck. Start by cutting the ends from the required wood square this will help with all the construction from the frame always cut the items of wood exactly the same length because frame won’t be square if the wood is of various lengths. Then join the corners from the frame by piloting the holes for your 4 inch screws to get screwed into wood. Once this is achieved you’ll want to get the frame square, using an engineers square install it in a corner and move until square. Then screw a batten inside corner to keep the corner square try this for all corners. Then measure internally from your horizontal from the frame in which the load bearers are getting divide this measurement by 600mm this can give you an identical spacing for your struts. Next screw theses available it is simpler to place a amount of wood underneath the frame while carrying this out to find the edges in order to meet. Once this is achieved measure the cross member struts about three feet is around right for your spacing of those. They go vertically along the deck frame stepping out then in to accommodate screwing.
Setting of the deck, get the deck into position with all the help of the friend. Then start inside highest corner of the deck and bang an item of cut 4 x 2 (depending for the height of the deck cut accordingly) to the ground with a large sledge hammer. Once done lift the deck into position and screw together with a 4 inch screw. Now work along the deck on the next horizontal corner lifts the corner hence the frame is level and do exactly the same. Now work along the front have a slight lean away from your house or make certain whichever way the boards are running tip the deck hence the water runs out from the surface. Then work your way across the deck making sure that any weak spot is supported by banging a piece of four x 2 to the ground beneath it. Once this is achieved test the strength by walking along the struts to show any weak spot no problem an excessive amount of because decking boards will strengthen the decking whenever they are fixed on the frame.
Right now we cut and suit the decking boards on the frame. Make sure every one of the edges from the decking are cut square before cutting on the correct length. This will aid construction and overall Finnish from the decking project. Start with a full amount of decking making sure the finish meets the frame or cut the board on the nearest beam and fasten the board with a Paslode nail gun using 50mm nails or pilot and countersink holes and screw the boards screwing is better lasting but nailing is faster and simpler. Work along the deck spacing with a 5mm nail banged right into a piece of four x 2, this can ensure that this gap remains exactly the same. Always remember to stagger the joints from the decking almost every other board hence the joints blend to the decking. Once you decking boards are fitted then fit any surrounding decking boards on the edges to pay for up any from the frame work and appearance for just about any boards that have splinters and sand these down if it is possible to.