Pros And Cons Wood Vs Composite Deck – Let’s begin first we have to look at the area can it be a turf or concrete base underneath the decking a turf base will have to be dug off and membrane put underneath the decking you can and should put membrane under any decking project to stop any weeds penetrating through, where include the damp course levels even as don’t want the deck over the damp course ideally the deck must be two bricks below the damp course. And can there be any drain access points underneath the decking as these need a special decking drain cover. Always remember the decking boards go horizontal along the home. Always remember decking higher that 1.2m over walk-out need planning permission
Now we have assessed these factors they are going to decide the height of the deck as well as any special requirements that have to be incorporated to the decking project. Estimation of materials first appraise the area of the decking i.e 4.8m x 4.8m = 23.04sq meters. Then make use of this equation to calculate the decking boards needed 4800mm / 140mm (deck board width which can be 4.8m long) = 35 decking boards. Add a little for cuts and edges that have to be filled in. Then calculate the burden bearing supports (4 x 2 pressure treated CLS) 4800 / 600 = 8 This the quantity of horizontal 4 x 2 pieces needed for the internal structure of the decking plus the outside of the frame i.e. 4800 x 4 = 19.2m + (8 x 4800) = 58m of 4 x 2. Add some for the cross member struts and positioning pegs (banged and concreted as needed to the ground) about three or four 4.8m lengths should suffice.
Establishing the frame this ought to be done near or as close for the position of the final deck. Start by cutting the ends of the required wood square this will help with the construction of the frame always cut the components of wood exactly the same length because the frame won’t be square in the event the wood is of various lengths. Then join the corners of the frame by piloting the holes for the 4 inch screws being screwed into wood. Once this is achieved you’ll want to obtain the frame square, utilizing an engineers square install it in one corner and move until square. Then screw a batten in the corner to carry the corner square try this for all corners. Then measure internally through the horizontal of the frame in which the load bearers are getting divide this measurement by 600mm this can provide you with the same spacing for the struts. Next screw theses set up it can be easier to place a length of wood underneath the frame while doing this to obtain the edges to satisfy. Once this is achieved appraise the cross member struts about three feet is approximately right for the spacing of the. They go vertically along the deck frame stepping out then into permit screwing.
Positioning of the deck, get the deck into position with the help of an friend. Then start in the highest corner of the deck and bang a piece of cut 4 x 2 (depending for the height of the deck cut accordingly) to the ground which has a large sledge hammer. Once done lift the deck into position and screw together which has a 4 inch screw. Now work along the deck for the next horizontal corner lifts the corner and so the frame is level and do exactly the same. Now work along the front use a slight lean away through the house or ensure whichever way the boards are running tip the deck and so the water runs out of the surface. Then work your way across the deck ensuring that any weak point is supported by banging a piece of 4 x 2 to the ground beneath it. Once this is achieved test the strength by walking along the struts to demonstrate any weak point don’t worry an excessive amount of because the decking boards will strengthen the decking when they are fixed for the frame.
Today we cut and fit in the decking boards for the frame. Make sure every one of the edges of the decking are cut square before cutting for the correct length. This will aid construction and overall Finnish of the decking project. Start which has a full length of decking ensuring the finish meets the frame or cut the board for the nearest beam and connect the board which has a Paslode nail gun using 50mm nails or pilot and countersink holes and screw the boards screwing is best long-term but nailing is faster and much easier. Work along the deck spacing which has a 5mm nail banged right into a piece of 4 x 2, this can ensure how the gap remains exactly the same. Always remember to stagger the joints of the decking every other board and so the joints blend to the decking. Once you decking boards are fitted then fit any surrounding decking boards for the edges to hide up any of the frame work and check for almost any boards which have splinters and sand these down if you can.