Azek Deck Fascia Board – Let’s begin first we have to measure the area can it be a turf or concrete base within the decking a turf base will have to be dug off and membrane put within the decking you are able to and should put membrane under any decking project to halt any weeds penetrating through, where would be the damp course levels even as don’t want occasions higher than the damp course ideally occasions must be two bricks below the damp course. And is there any drain access points within the decking as these need a particular decking drain cover. Always remember the decking boards go horizontal along the home. Always remember decking higher that 1.2m over walk out need planning permission
Now we now have assessed these factors they’ll decide the height of occasions and any special requirements that have to be incorporated in to the decking project. Estimation of materials first measure the area in the decking i.e 4.8m x 4.8m = 23.04sq meters. Then utilize this equation to calculate the decking boards needed 4800mm / 140mm (deck board width that happen to be 4.8m long) = 35 decking boards. Add a little for cuts and edges that have to be filled in. Then calculate the burden bearing supports (4 x 2 pressure treated CLS) 4800 / 600 = 8 This the quantity of horizontal 4 x 2 pieces needed for the internal structure in the decking in addition to the outside in the frame i.e. 4800 x 4 = 19.2m + (8 x 4800) = 58m of four x 2. Add some for the cross member struts and positioning pegs (banged and concreted if needed in to the ground) about three to four 4.8m lengths should suffice.
Setting up the frame this should be done near or as close for the position in the final deck. Start by cutting the ends in the required wood square this will help with all the construction in the frame always cut the pieces of wood the same length since the frame won’t be square when the wood is of lengths. Then join the corners in the frame by piloting the holes for the 4 inch screws to get screwed into wood. Once this is done you need to have the frame square, having an engineers square put it in one corner and move until square. Then screw a batten inside the corner to carry the corner square do this for those corners. Then measure internally in the horizontal in the frame where the load bearers are inclined divide this measurement by 600mm this will provide you with the same spacing for the struts. Next screw theses in position it’s simpler to place a length of wood within the frame while achieving this to have the edges to satisfy. Once this is done measure the cross member struts about three feet is about right for the spacing of the. They go vertically along occasions frame stepping out then straight into accommodate screwing.
Ranking of occasions, get occasions into position with all the help of your friend. Then start inside the highest corner of occasions and bang an item of cut 4 x 2 (depending for the height of occasions cut accordingly) in to the ground using a large sledge hammer. Once done lift occasions into position and screw together using a 4 inch screw. Now work along occasions for the next horizontal corner lifts the corner therefore the frame is level and do the same. Now work across the front have a slight lean away in the house or ensure whichever way the boards are running tip occasions therefore the water runs out in the surface. Then work your way across occasions making sure that any a weakness is sustained by banging a piece of four x 2 in to the ground beneath it. Once this is done test the strength by walking across the struts to exhibit any a weakness don’t worry a lot of since the decking boards will strengthen the decking when they are fixed for the frame.
Right now we cut and fit the decking boards for the frame. Make sure every one of the edges in the decking are cut square before cutting for the correct length. This will aid construction and overall Finnish in the decking project. Start using a full length of decking making sure the conclusion meets the frame or cut the board for the nearest beam and connect the board using a Paslode nail gun using 50mm nails or pilot and countersink holes and screw the boards screwing is best lasting but nailing is faster and easier. Work along occasions spacing using a 5mm nail banged in a piece of four x 2, this will ensure the gap remains the same. Always remember to stagger the joints in the decking every other board therefore the joints blend in to the decking. Once you decking boards are fitted then fit any surrounding decking boards for the edges to hide up any in the frame work and look for any boards who have splinters and sand these down if you are able to.