Face Screwing Deck Boards – A few begin first we need to assess the area would it be a turf or concrete base within the decking a turf base will should be dug off and membrane put within the decking it is possible to and may put membrane under any decking project to avoid any weeds penetrating through, where are the damp course levels once we don’t need those times across the damp course ideally those times must be two bricks below the damp course. And is there any drain access points within the decking as these will require an exclusive decking drain cover. Always remember the decking boards go horizontal along your home. Always remember decking higher that 1.2m from the ground level will require planning permission
Now we’ve got assessed these factors they’re going to decide the height of those times as well as any special requirements that should be incorporated in the decking project. Estimation of materials first measure the area from the decking i.e 4.8m x 4.8m = 23.04sq meters. Then make use of this equation to calculate the decking boards needed 4800mm / 140mm (deck board width which can be 4.8m long) = 35 decking boards. Add a little for cuts and edges that should be filled in. Then calculate the load bearing supports (4 x 2 pressure treated CLS) 4800 / 600 = 8 This the quantity of horizontal 4 x 2 pieces needed for your internal structure from the decking plus the outside from the frame i.e. 4800 x 4 = 19.2m + (8 x 4800) = 58m of four years old x 2. Add some for your cross member struts and positioning pegs (banged and concreted as required in the ground) about 3 or 4 4.8m lengths should suffice.
Building the frame this should be done near or as close for the position from the final deck. Start by cutting the ends from the required wood square this can help using the construction from the frame always cut the pieces of wood a similar length because frame won’t be square if your wood is of different lengths. Then join the corners from the frame by piloting the holes for your 4 inch screws to become screwed into wood. Once this can be done you’ll want to have the frame square, using an engineers square install it in a corner and move until square. Then screw a batten inside corner to support the corner square try this for all corners. Then measure internally from the horizontal from the frame in which the load bearers are going divide this measurement by 600mm this will likely give you the same spacing for your struts. Next screw theses set up it really is simpler to place a duration of wood within the frame while achieving this to have the edges to meet. Once this can be done measure the cross member struts about three feet is about right for your spacing of such. They go vertically along those times frame stepping out then in to allow for screwing.
Ranking of those times, get those times into position using the help of a friend. Then start inside highest corner of those times and bang an item of cut 4 x 2 (depending for the height of those times cut accordingly) in the ground with a large sledge hammer. Once done lift those times into position and screw together with a 4 inch screw. Now work along those times for the next horizontal corner lifts the corner so the frame is level and do a similar. Now work along the front have a very slight lean away from the house or be sure whichever way the boards are running tip those times so the water runs out from the surface. Then work your way across those times ensuring that that any some weakness is based on banging a piece of four years old x 2 in the ground beneath it. Once this can be done test the strength by walking along the struts to show any some weakness no problem excessive because decking boards will strengthen the decking once they are fixed for the frame.
Today we cut and fit in the decking boards for the frame. Make sure every one of the edges from the decking are cut square before cutting for the correct length. This will aid construction and overall Finnish from the decking project. Start with a full duration of decking ensuring that the end meets the frame or cut the board for the nearest beam and connect the board with a Paslode nail gun using 50mm nails or pilot and countersink holes and screw the boards screwing is better lasting but nailing is faster and easier. Work along those times spacing with a 5mm nail banged into a piece of four years old x 2, this will likely ensure that this gap remains a similar. Always remember to stagger the joints from the decking every other board so the joints blend in the decking. Once you decking boards are fitted then fit any surrounding decking boards for the edges to cover up any from the frame work and look for any boards which have splinters and sand these down if it is possible to.