Outdoor Oscillating Ceiling Fan – The flush-style ceiling fan is mounted snugly beside a set horizontal fairly low ceiling where it’s dealt with, and from where it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, with regards to the size of room being fitted, and may cost typically from $30 to $300. It generally has three fan motor speeds, which can be reversible. Except for the instruments and possible the rest needed for installing them, their self-assemble kits feature any devices. In many cases, the fan, that will have its lighting, will replace a ceiling permanent fixture.
Safety, The electricity should be off at the site the place that the fan is usually to be installed. If the fan is replacing a permanent fixture, turn off its fuse or circuit breaker along with flipping its wall switch to the off position. Stand on a sturdy wide-berth step stool or ladder during the installation; don’t lean or enter into a twisted position while there. Also, wear protective eyeglasses or goggles. Furthermore, if additional auxiliary household wiring is needed, get professional advice or help first. Tools needed, instructions (electrical) eyeglasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and further screws for securing the junction box, if required
Installation steps (seeing the fan installation instructions thoroughly). 1. Remove the permanent fixture from the ceiling. With the electricity off, slowly eliminate the shade, bulbs, and fixture screws from the electrical junction box inside the ceiling. Let the skeleton fixture hang there. With the light tester, ensure the wire connections for this fixture are cold (the test light will continue to be off). Cut the wires, leaving 3-5″ of tail for connecting the crooks to the ceiling fan motor assembly. If the house is old, only two wires might exist, a black one plus a white one. Tip: also confirm the firmness from the electrical box inside the ceiling. If it’s not solidly coupled to the ceiling, add two extra screws to its top side, which can require drilling two holes inside the box for them. The ceiling fan is heavier compared to permanent fixture. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends from the tailing wires inside the junction box cleanly, install the mounting bracket for the box while using two 5/32″ screw-bolts provided. Let the tailing wires hang outside from the bracket. 3. Hang the motor assembly from the bracket. Insert the topside motor-hanger in the centralized holder from the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly is supposed to swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one for that motor plus a blue or off-color one for that lights to get attached below it. Overlap the stripped ends of those two wires (motor and lights) together while using stripped end from the black ceiling wire inside the box, and twist connect them together while using wire nut provided. Connect the white assembly wire for the white ceiling wire exactly the same.
Then, to help keep these connections from loosening whilst the fan is working, tape the wide lower ends of those nuts on their wires with electrical tape. Also, attach the green fan wire (ground wire from the bracket frame) for the electrical box if the box is also grounded using a third bare or green wire. Otherwise, if the electrical box in not grounded, ask an expert about it green wire connection. Some will say to let it rest be, i.e., relax by using it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud for the far ends from the mounting bracket while using small screws provided. It covers/hides the edges from the motor as well as the wiring and ceiling box. 6. Assemble the fan blades (four to six) and mount them. After deciding on the top or bottom reversible blade color scheme preferred, attach the blades on their end brackets while using screws and washers provided. Then mount the blades for the bottom side of fan motor while using bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed for the motor to help keep them separate from the rest from the kit hardware.
Tip: to help keep the motor from becoming too off-level within this step, install the blades one by one opposite to each other to begin with. 7. Install the lighting assembly. Attach the fan’s lighting assembly for the small round central housing unit just underneath the fan blades using the quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders inside the order instructed. Note: a housing cap is provided if the lighting assembly isn’t wanted for any reason. 8. Test the fan and lights. After turning the electricity back on, flip the wall switch to on. Set the pull-chain switches as desired. Often, the fan lighting is set ahead on while using wall switch, whilst the fan itself is controlled through the pull-chain switch only, initially set inside the off position. Note: The ceiling fan carries a reversible motor switch that permits the draft either to go upward or downward as preferred. For more information on ceiling fan installation, understand the following sites.