Chapter Ceiling Fan – Two top reasons to use a ceiling fan, cooling and heating. If you live in a very cold climate, fans can push heated air gathered at the ceiling back down. Ceiling fans might be an easy task to install when you have some mechanical aptitude. Current ceiling fans include remote-controls to vary speed and adjust lighting. If your room already features a permanent fixture in the ceiling, your permanent fixture probably has one hot or feed wire gonna it, the neutral white as well as the bonding green or copper. Essentially this can be a three-wire system. Many new construction homes have four wires available, one to the light the other to the fan motor control as well as the neutral and ground. If you only have one Hot wire feeding the ceiling junction box, the remote-control fans will work together with your application. Additionally some remote-controlled fans use wall controller which sends its signal to the fan being a TV remote. It just seems like a wall control unit. If you only need the ability wire for the remote-controlled fan, please cap from the fourth wire which you will not need to work with. This should be shown inside your directions that came with the fan assembly.
Once you might have acquired a lover that suits you, assemble it according to the instructions given. Some fans certainly are a extra complex, ask a pal to help if necessary. It is best to makes it assembled correctly, having a ceiling fan blade thud yourself on the top might be annoying. Once you might have the pre-assembly completed, now you can prepare the ceiling junction box. Of course I know you might have already made sure the ability to the ceiling box is turned off with no one can energize it accidentally. Once you might have performed this, you ought to find three wires in the J-box. A copper or green wire for bonding. A white wire to the neutral as well as a red or black wire to the power. If your junction box features a fourth wire, this would be create for any wall controlled fan switch which can be great and allows you to work with a non-remote wall controller. I should mention that some all fans include a wall controllers designed as remotes so don’t be confused because these all use the singular feed inside your ceiling junction box.
A word about weight, not yours but a word regarding the size your fan. If you might have a large fan and its particular weighted near 12 pounds or even more, you may need a special junction box that may secure the extra body fat. I would recommend you may well ask someone who knows about these heavier fans if that’s what you’re gonna install. Most fans are lighter and might be set up in most junction boxes without modifications.
Now we should get it down there, the fan that’s. Many fans include a Hanger the same shape as a U. Install this hanger onto your box, the screws should be 8/32 types. That means a size 8 diameter or gauge screw with 32 threads per inch. Once you might have the hanger installed, grab your fan motor minus the blades installed and place it around the hanger. This allows you the electrician to get together the wires without struggling to juggle the motor and wire it concurrently. Connect the bonding wire to the chassis as noted in the instructions. Next connect the white neutral wire, now the black wire. Swing the fan into place while using parts provided. Some have brackets, some work with a metal plate while others use preformed mounting bases. Use your instructions you may have a lover quickly. Smaller fans may necessitate you to pre-assemble your blades before hanging the fan. I always found installing the motor first and after that installing the blades last is easier. It does require however, you to work above your face to get the blades attached.
Once you might have the fan hanging, the blades installed and everything tightened now you can step from the ladder, relax, then install the wall controller as provided. These all vary in design however they all follow similar procedures. Remember, you will find a line and load situation here. This means, the line side may be the group of wires the feed to the switch box from your panel while the Load side is gonna your fan. This is critical so be sure you understand the difference. Connect the Load side first: Connect your bonding wire first. Then connect your white neutral wire. Then your hot wire. Next do the Line (incoming) side next: Bond or ground should already be constructed to the new controller. Next wire your white neutral to the controllers neutral to the Line side. You may have already wired your neutrals together as outlined by your instructions. Now wire your Hot or Power wire to the Line side of one’s controller. If you might have the fourth wire within, cap it off or use it to the motor control and connect it accordingly for your directions. Red to Red is usually the case here. Once completed, get yourself some Iced Tea and get your new fan.