Fan Switch For Ceiling Fan – The flush-style ceiling fan is mounted snugly close to a set horizontal fairly low ceiling where it’s taken care of, and from which it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, according to the room size being fitted, and can cost typically from $30 to $300. It generally has three fan motor speeds, which can be reversible. Except for the tools and possible other areas necessary for installing them, their self-assemble kits come with everything else. In many cases, the fan, which will have its very own lighting, will replace a ceiling fitting.
Safety, The electricity should be off to begin the location where the fan shall be installed. If the fan is replacing a fitting, de-activate its fuse or circuit breaker in addition to flipping its wall switch to the off position. Stand on a sturdy wide-berth step stool or ladder throughout the installation; don’t lean or enter into a twisted position while there. Also, wear protective eye glasses or goggles. Furthermore, if additional auxiliary household wiring is necessary, get professional advice or help first. Tools needed, instructions (electrical) eye glasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and additional screws for securing the junction box, as appropriate
Installation steps (after reading the fan installation instructions thoroughly). 1. Remove the fitting through the ceiling. With the electricity off, slowly remove the shade, bulbs, and fixture screws through the electrical junction box inside the ceiling. Let the skeleton fixture hang there. With the light tester, ensure that the wire connections to this fixture are cold (quality light will stay off). Cut the wires, leaving 3-5″ of tail in order to connect the crooks to the ceiling fan motor assembly. If the property is old, only two wires might exist, a black one and a white one. Tip: also check the firmness with the electrical box inside the ceiling. If it’s not solidly attached to the ceiling, add two extra screws to its top side, that might require drilling two holes inside the box for them. The ceiling fan is heavier compared to the fitting. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends with the tailing wires inside the junction box cleanly, install the mounting bracket on the box while using two 5/32″ screw-bolts provided. Let the tailing wires hang outside with the bracket. 3. Hang the motor assembly through the bracket. Insert the topside motor-hanger to the centralized holder with the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly should really swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one to the motor and a blue or off-color one to the lights being attached below it. Overlap the stripped ends of such two wires (motor and lights) together while using stripped end with the black ceiling wire inside the box, and twist connect them together while using wire nut provided. Connect the white assembly wire on the white ceiling wire exactly the same way.
Then, to keep these connections from loosening whilst the fan is working, tape the wide lower ends of such nuts on their wires with electrical tape. Also, attach the green fan wire (ground wire through the bracket frame) on the electrical box in the event the box is additionally grounded with a third bare or green wire. Otherwise, in the event the electrical box in not grounded, ask an expert about it green wire connection. Some will say to let it sit be, i.e., do nothing with it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud on the far ends with the mounting bracket while using small screws provided. It covers/hides the edges with the motor and also the wiring and ceiling box. 6. Assemble the fan blades (3 to 4) and mount them. After deciding on the top or bottom reversible blade color scheme preferred, attach the blades on their end brackets while using screws and washers provided. Then mount the blades on the bottom side of fan motor while using bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed on the motor to keep them separate through the rest with the kit hardware.
Tip: to keep the motor from becoming too off-level within this step, install the blades one-by-one opposite to one another in the first place. 7. Install the lighting assembly. Attach the fan’s lighting assembly on the small round central housing unit just under the fan blades through quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders inside the order instructed. Note: a housing cap is provided in the event the lighting assembly just isn’t wanted without any reason. 8. Test the fan and lights. After turning the electricity back on, flip the wall switch to on. Set the pull-chain switches as desired. Often, the fan lighting is set in the future on while using wall switch, whilst the fan itself is controlled from the pull-chain switch only, initially set inside the off position. Note: The ceiling fan includes a reversible motor switch that permits the draft either to go upward or downward as preferred. For more information on ceiling fan installation, begin to see the following sites.