Tropical Outdoor Ceiling Fans – The flush-style ceiling fan is mounted snugly close to a flat horizontal fairly low ceiling where it can be out of the way, and from where it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, with regards to the size of the room being fitted, and may cost typically from $30 to $300. It generally has three fan motor speeds, which can be reversible. Except for the instruments and possible other regions required for installing them, their self-assemble kits include everything else. In many cases, the fan, which will have its very own lighting, will replace a ceiling fitting.
Safety, The electricity have to be off at the site the place that the fan is to be installed. If the fan is replacing a fitting, turn off its fuse or circuit breaker along with flipping its wall switch the signal from the off position. Stand on a sturdy wide-berth step stool or ladder in the installation; don’t lean or end up in a twisted position while there. Also, wear protective eye-glasses or goggles. Furthermore, if additional auxiliary household wiring is necessary, get professional advice or help first. Tools needed, instructions (electrical) eye-glasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and further screws for securing the junction box, if needed
Installation steps (reading the fan installation instructions thoroughly). 1. Remove the fitting through the ceiling. With the electricity off, slowly eliminate the shade, bulbs, and fixture screws through the electrical junction box within the ceiling. Let the skeleton fixture hang there. With the light tester, ensure that the wire connections to this fixture are cold (the test light will stay off). Cut the wires, leaving 3-5″ of tail to get in touch the crooks to the ceiling fan motor assembly. If the home is old, only two wires might exist, a black one and a white one. Tip: also look into the firmness from the electrical box within the ceiling. If it can be not solidly attached to the ceiling, add two extra screws to its top side, which could require drilling two holes within the box for the kids. The ceiling fan is heavier compared to fitting. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends from the tailing wires within the junction box cleanly, install the mounting bracket to the box with all the two 5/32″ screw-bolts provided. Let the tailing wires hang outside from the bracket. 3. Hang the motor assembly through the bracket. Insert the topside motor-hanger in to the centralized holder from the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly should really swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one for the motor and a blue or off-color one for the lights to get attached below it. Overlap the stripped ends of those two wires (motor and lights) together with all the stripped end from the black ceiling wire within the box, and twist connect them together with all the wire nut provided. Connect the white assembly wire to the white ceiling wire exactly the same way.
Then, to maintain these connections from loosening while the fan is working, tape the wide lower ends of those nuts to their wires with electrical tape. Also, attach the green fan wire (ground wire through the bracket frame) to the electrical box when the box is additionally grounded having a third bare or green wire. Otherwise, when the electrical box in not grounded, ask an expert relating to this green wire connection. Some will say to let it sit be, i.e., do nothing from it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud to the far ends from the mounting bracket with all the small screws provided. It covers/hides the edges from the motor and also the wiring and ceiling box. 6. Assemble the fan blades (3 to 4) and mount them. After picking out the top or bottom reversible blade color scheme preferred, attach the blades to their end brackets with all the screws and washers provided. Then mount the blades to the bottom side of fan motor with all the bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed to the motor to maintain them separate through the rest from the kit hardware.
Tip: to maintain the motor from becoming too off-level with this step, install the blades one-by-one opposite together first of all. 7. Install the lighting assembly. Attach the fan’s lighting assembly to the small round central housing unit just below the fan blades using the quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders within the order instructed. Note: a housing cap is provided when the lighting assembly just isn’t wanted unconditionally. 8. Test the fan and lights. After turning the electricity back on, flip the wall switch the signal from on. Set the pull-chain switches as desired. Often, the fan lighting is set into the future on with all the wall switch, while the fan itself is controlled through the pull-chain switch only, initially set within the off position. Note: The ceiling fan features a reversible motor switch that allows the draft either to go upward or downward as preferred. For more information on ceiling fan installation, begin to see the following sites.