Garage Ceiling Fan With Light – The flush-style ceiling fan is mounted snugly alongside a set horizontal fairly low ceiling where it can be dealt with, and from where it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, with respect to the size of room being fitted, which enable it to cost typically from $30 to $300. It generally has three fan motor speeds, that are reversible. Except for the instruments and possible other parts needed for installing them, their self-assemble kits include any devices. In many cases, the fan, which will have its own lighting, will replace a ceiling permanent fixture.
Safety, The electricity should be off once your there the place that the fan is usually to be installed. If the fan is replacing a permanent fixture, power down its fuse or circuit breaker along with flipping its wall exchange signal of the off position. Stand on a sturdy wide-berth step stool or ladder throughout the installation; do not lean or enter into a twisted position while there. Also, wear protective eye-glasses or goggles. Furthermore, if additional auxiliary household wiring is needed, get professional advice or help first. Tools needed, instructions (electrical) eye-glasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and extra screws for securing the junction box, if required
Installation steps (looking at the fan installation instructions thoroughly). 1. Remove the permanent fixture from your ceiling. With the electricity off, slowly take away the shade, bulbs, and fixture screws from your electrical junction box in the ceiling. Let the skeleton fixture hang there. With the light tester, guarantee the wire connections to the fixture are cold (quality light will always be off). Cut the wires, leaving 3-5″ of tail to get in touch these to the ceiling fan motor assembly. If the property is old, only two wires might exist, a black one plus a white one. Tip: also check the firmness from the electrical box in the ceiling. If it can be not solidly coupled to the ceiling, add two extra screws to its top side, which might require drilling two holes in the box on their behalf. The ceiling fan is heavier than the permanent fixture. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends from the tailing wires in the junction box cleanly, install the mounting bracket to the box using the two 5/32″ screw-bolts provided. Let the tailing wires hang outside from the bracket. 3. Hang the motor assembly from your bracket. Insert the topside motor-hanger to the centralized holder from the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly is supposed to swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one for your motor plus a blue or off-color one for your lights being attached below it. Overlap the stripped ends of the two wires (motor and lights) together using the stripped end from the black ceiling wire in the box, and twist connect them together using the wire nut provided. Connect the white assembly wire to the white ceiling wire exactly the same.
Then, to keep these connections from loosening as the fan is working, tape the wide lower ends of the nuts to their wires with electrical tape. Also, attach the green fan wire (ground wire from your bracket frame) to the electrical box when the box can be grounded using a third bare or green wire. Otherwise, when the electrical box in not grounded, ask an experienced about this green wire connection. Some will say to get forced out be, i.e., relax from it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud to the far ends from the mounting bracket using the small screws provided. It covers/hides the perimeters from the motor and the wiring and ceiling box. 6. Assemble the fan blades (3 to 4) and mount them. After deciding on the top or bottom reversible blade color scheme preferred, attach the blades to their end brackets using the screws and washers provided. Then mount the blades to the bottom side of fan motor using the bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed to the motor to keep them separate from your rest from the kit hardware.
Tip: to keep the motor from becoming too off-level within this step, install the blades individually opposite to one another to begin with. 7. Install the lighting assembly. Attach the fan’s lighting assembly to the small round central housing unit just below the fan blades through quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders in the order instructed. Note: a housing cap is provided when the lighting assembly just isn’t wanted unconditionally. 8. Test the fan and lights. After turning the electricity back on, flip the wall exchange signal of on. Set the pull-chain switches as desired. Often, the fan lighting is set into the future on using the wall switch, as the fan itself is controlled with the pull-chain switch only, initially set in the off position. Note: The ceiling fan has a reversible motor switch that permits the draft either to go upward or downward as preferred. For more information on ceiling fan installation, start to see the following sites.