Hugger Style Ceiling Fan – The flush-style ceiling fan is mounted snugly alongside a set horizontal fairly low ceiling where it can be out of the way, and where it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, with regards to the room size being fitted, which enable it to cost typically from $30 to $300. It generally has three fan motor speeds, which are reversible. Except for the instruments and possible other parts necessary for installing them, their self-assemble kits include any devices. In many cases, the fan, that can have its very own lighting, will replace a ceiling light fixture.
Safety, The electricity should be off once your there where the fan will be installed. If the fan is replacing a light fixture, shut down its fuse or circuit breaker together with flipping its wall switch the signal from the off position. Stand on a sturdy wide-berth step stool or ladder throughout the installation; usually do not lean or enter into a twisted position while there. Also, wear protective eye glasses or goggles. Furthermore, if additional auxiliary household wiring should be used, get professional advice or help first. Tools needed, instructions (electrical) eye glasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and extra screws for securing the junction box, if necessary
Installation steps (after reading the fan installation instructions thoroughly). 1. Remove the light fixture in the ceiling. With the electricity off, slowly get rid of the shade, bulbs, and fixture screws in the electrical junction box within the ceiling. Let the skeleton fixture hang there. With the light tester, guarantee the wire connections for this fixture are cold (test light will always be off). Cut the wires, leaving 3-5″ of tail allowing you to connect these to the ceiling fan motor assembly. If the property is old, only two wires might exist, a black one as well as a white one. Tip: also confirm the firmness with the electrical box within the ceiling. If it can be not solidly connected to the ceiling, add two extra screws to its top side, which might require drilling two holes within the box for the children. The ceiling fan is heavier compared to the light fixture. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends with the tailing wires within the junction box cleanly, install the mounting bracket to the box while using two 5/32″ screw-bolts provided. Let the tailing wires hang outside with the bracket. 3. Hang the motor assembly in the bracket. Insert the topside motor-hanger in the centralized holder with the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly is supposed to swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one for your motor as well as a blue or off-color one for your lights being attached below it. Overlap the stripped ends of those two wires (motor and lights) together while using stripped end with the black ceiling wire within the box, and twist connect them together while using wire nut provided. Connect the white assembly wire to the white ceiling wire the same way.
Then, to hold these connections from loosening as the fan is working, tape the wide lower ends of those nuts to their wires with electrical tape. Also, attach the green fan wire (ground wire in the bracket frame) to the electrical box if your box can also be grounded having a third bare or green wire. Otherwise, if your electrical box in not grounded, ask an expert relating to this green wire connection. Some will say to get forced out be, i.e., do nothing by it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud to the far ends with the mounting bracket while using small screws provided. It covers/hides the edges with the motor as well as the wiring and ceiling box. 6. Assemble the fan blades (4 to 6) and mount them. After seeking the top or bottom reversible blade color scheme preferred, attach the blades to their end brackets while using screws and washers provided. Then mount the blades to the bottom side of fan motor while using bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed to the motor to hold them separate in the rest with the kit hardware.
Tip: to hold the motor from becoming too off-level in this step, install the blades one at a time opposite together to start with. 7. Install the lighting assembly. Attach the fan’s lighting assembly to the small round central housing unit just beneath the fan blades via the quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders within the order instructed. Note: a housing cap is provided if your lighting assembly is just not wanted for any reason. 8. Test the fan and lights. After turning the electricity back on, flip the wall switch the signal from on. Set the pull-chain switches as desired. Often, the fan lighting is set to come on while using wall switch, as the fan itself is controlled with the pull-chain switch only, initially set within the off position. Note: The ceiling fan has a reversible motor switch which allows the draft either to go upward or downward as preferred. For more information on ceiling fan installation, start to see the following sites.