Flush Mount Ceiling Fans Without Lights – The flush-style ceiling fan is mounted snugly beside a designated horizontal fairly low ceiling where it is dealt with, and from which it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, according to the size of room being fitted, and will cost typically from $30 to $300. It generally has three fan motor speeds, that are reversible. Except for the tools and possible other regions necessary for installing them, their self-assemble kits have everything else. In many cases, the fan, that may have a unique lighting, will replace a ceiling light fixture.
Safety, The electricity have to be off at the site in which the fan is to be installed. If the fan is replacing a light fixture, power down its fuse or circuit breaker in addition to flipping its wall switch the signal from the off position. Stand on a sturdy wide-berth step stool or ladder during the installation; usually do not lean or get into a twisted position while there. Also, wear protective eye-glasses or goggles. Furthermore, if additional auxiliary household wiring is required, get professional advice or help first. Tools needed, instructions (electrical) eye-glasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and further screws for securing the junction box, if needed
Installation steps (reading the fan installation instructions thoroughly). 1. Remove the light fixture from your ceiling. With the electricity off, slowly eliminate the shade, bulbs, and fixture screws from your electrical junction box inside ceiling. Let the skeleton fixture hang there. With the light tester, ensure the wire connections for this fixture are cold (the exam light will stay off). Cut the wires, leaving 3-5″ of tail in order to connect these to the ceiling fan motor assembly. If the home is old, only two wires might exist, a black one and a white one. Tip: also look into the firmness of the electrical box inside ceiling. If it is not solidly coupled to the ceiling, add two extra screws to its top side, which might require drilling two holes inside box on their behalf. The ceiling fan is heavier compared to the light fixture. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends of the tailing wires inside junction box cleanly, install the mounting bracket towards the box while using two 5/32″ screw-bolts provided. Let the tailing wires hang outside of the bracket. 3. Hang the motor assembly from your bracket. Insert the topside motor-hanger in the centralized holder of the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly is supposed to swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one for the motor and a blue or off-color one for the lights to become attached below it. Overlap the stripped ends of those two wires (motor and lights) together while using stripped end of the black ceiling wire inside box, and twist connect them together while using wire nut provided. Connect the white assembly wire towards the white ceiling wire exactly the same.
Then, to maintain these connections from loosening while the fan is working, tape the wide lower ends of those nuts for their wires with electrical tape. Also, attach the green fan wire (ground wire from your bracket frame) towards the electrical box if the box can be grounded using a third bare or green wire. Otherwise, if the electrical box in not grounded, ask an experienced about this green wire connection. Some will say to let it sit be, i.e., do nothing from it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud towards the far ends of the mounting bracket while using small screws provided. It covers/hides the perimeters of the motor and also the wiring and ceiling box. 6. Assemble the fan blades (4 to 6) and mount them. After picking out the top or bottom reversible blade color scheme preferred, attach the blades for their end brackets while using screws and washers provided. Then mount the blades towards the bottom side of fan motor while using bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed towards the motor to maintain them separate from your rest of the kit hardware.
Tip: to maintain the motor from becoming too off-level with this step, install the blades individually opposite together in the first place. 7. Install the lighting assembly. Attach the fan’s lighting assembly towards the small round central housing unit just below the fan blades using the quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders inside order instructed. Note: a housing cap is provided if the lighting assembly is not wanted at all. 8. Test the fan and lights. After turning the electricity back on, flip the wall switch the signal from on. Set the pull-chain switches as desired. Often, the fan lighting is set to come on while using wall switch, while the fan itself is controlled by the pull-chain switch only, initially set inside off position. Note: The ceiling fan features a reversible motor switch which allows the draft either to go upward or downward as preferred. For more information on ceiling fan installation, see the following sites.