2 Fan Ceiling Fan – Two why you should use a ceiling fan, cooling and heating. If you live inside a cold climate, fans can push hot air gathered close to the ceiling down again. Ceiling fans might be easy to install in case you have some mechanical aptitude. Current ceiling fans come with remote-controls to vary speed and adjust lighting. If your room already carries a light fixture inside ceiling, your light fixture probably has one hot or feed wire likely to it, the neutral white and also the bonding green or copper. Essentially it is a three-wire system. Many new construction homes have four wires available, one for the light and one for the fan motor control and also the neutral and ground. If you have only one Hot wire feeding the ceiling junction box, the remote-control fans will continue to work together with your application. Additionally some remote-controlled fans use wall controller which sends its signal towards the fan as being a TV remote. It just appears to be a wall control unit. If you only need the energy wire for the remote-controlled fan, please cap over fourth wire which you will n’t need to use. This needs to be shown inside your directions that included the fan assembly.
Once you have acquired a fan that suits you, put it together according towards the instructions given. Some fans can be a much more complex, ask a buddy to help you if required. It is best to makes it assembled correctly, creating a ceiling fan blade thud yourself on your head might be annoying. Once you have the pre-assembly completed, you can now prepare the ceiling junction box. Of course I know you have already ensured the energy towards the ceiling box is turned off no one can energize it accidentally. Once you have carried this out, you must find three wires inside J-box. A copper or green wire for bonding. A white wire for the neutral plus a red or black wire for the power. If your junction box carries a fourth wire, this is set up for any wall controlled fan switch which can be great and allows you to use a non-remote wall controller. I should mention that some all fans come with a wall controllers designed as remotes so avoid being confused as these all help the singular feed inside your ceiling junction box.
A word about weight, not yours but a thing concerning the size your fan. If you have a big fan and its particular weighted near 12 pounds or more, you may need a special junction box that may support the excess weight. I would recommend you may well ask someone that knows about these heavier fans recommendations what you are likely to install. Most fans are lighter and might be installed in most junction boxes without modifications.
Now we should get up there, the fan which is. Many fans come with a Hanger the same shape as a U. Install this hanger on to your box, the screws needs to be 8/32 types. That means a size 8 diameter or gauge screw with 32 threads per inch. Once you have the hanger installed, pick-up your fan motor with no blades installed and place it around the hanger. This allows you the electrician to attach the wires without struggling to juggle the motor and wire it at the same time. Connect the bonding wire towards the chassis as noted inside instructions. Next connect the white neutral wire, and after this the black wire. Swing the fan into place while using parts provided. Some have brackets, some utilize a metal plate and some use preformed mounting bases. Use your instructions and you’ll have a fan right away. Smaller fans may need that you pre-assemble your blades before hanging the fan. I always found installing the motor first and then installing the blades last is much easier. It does require however, that you work above your head to find the blades attached.
Once you have the fan hanging, the blades installed and everything tightened you can now step over ladder, breathe deeply, then install the wall controller as provided. These all vary in design but they all follow similar procedures. Remember, you will have line and load situation here. This means, the queue side is the pair of wires the feed into the switch box from the panel as the Load side is likely to your fan. This is critical so be sure you see the difference. Connect the Load side first: Connect your bonding wire first. Then connect your white neutral wire. Then your hot wire. Next do the Line (incoming) side next: Bond or ground should already be composed towards the new controller. Next wire your white neutral towards the controllers neutral for the Line side. You may have already wired your neutrals together in accordance with your instructions. Now wire your Hot or Power wire towards the Line side of one’s controller. If you have the fourth wire inside, cap it off or use it for the motor control and connect it accordingly for your directions. Red to Red is usually the case here. Once completed, get yourself some Iced Tea and get your brand-new fan.