Homekit Ceiling Fan – The flush-style ceiling fan is mounted snugly beside a flat horizontal fairly low ceiling where it really is taken care of, and from where it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, with respect to the size of room being fitted, and may cost typically from $30 to $300. It generally has three fan motor speeds, that happen to be reversible. Except for the equipment and possible other areas required for installing them, their self-assemble kits come with anything else. In many cases, the fan, that can have its very own lighting, will replace a ceiling light fixture.
Safety, The electricity should be off once your there where the fan shall be installed. If the fan is replacing a light fixture, turn off its fuse or circuit breaker in addition to flipping its wall switch to the off position. Stand on a sturdy wide-berth step stool or ladder in the installation; do not lean or get into a twisted position while there. Also, wear protective eyeglasses or goggles. Furthermore, if additional auxiliary household wiring should be used, get professional advice or help first. Tools needed, instructions (electrical) eyeglasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and further screws for securing the junction box, as appropriate
Installation steps (seeing the fan installation instructions thoroughly). 1. Remove the light fixture from the ceiling. With the electricity off, slowly eliminate the shade, bulbs, and fixture screws from the electrical junction box in the ceiling. Let the skeleton fixture hang there. With the light tester, make sure the wire connections to this particular fixture are cold (test light will remain off). Cut the wires, leaving 3-5″ of tail in order to connect these phones the ceiling fan motor assembly. If the residence is old, only two wires might exist, a black one as well as a white one. Tip: also look at the firmness from the electrical box in the ceiling. If it really is not solidly attached to the ceiling, add two extra screws to its top side, which could require drilling two holes in the box on their behalf. The ceiling fan is heavier as opposed to light fixture. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends from the tailing wires in the junction box cleanly, install the mounting bracket on the box with all the two 5/32″ screw-bolts provided. Let the tailing wires hang outside from the bracket. 3. Hang the motor assembly from the bracket. Insert the topside motor-hanger to the centralized holder from the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly should really swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one for your motor as well as a blue or off-color one for your lights being attached below it. Overlap the stripped ends of those two wires (motor and lights) together with all the stripped end from the black ceiling wire in the box, and twist connect them together with all the wire nut provided. Connect the white assembly wire on the white ceiling wire exactly the same.
Then, to hold these connections from loosening even though the fan is working, tape the wide lower ends of those nuts with their wires with electrical tape. Also, attach the green fan wire (ground wire from the bracket frame) on the electrical box if your box can be grounded having a third bare or green wire. Otherwise, if your electrical box in not grounded, ask an experienced about this green wire connection. Some will say to let it sit be, i.e., do nothing by it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud on the far ends from the mounting bracket with all the small screws provided. It covers/hides the sides from the motor and also the wiring and ceiling box. 6. Assemble the fan blades (3 to 4) and mount them. After seeking the top or bottom reversible blade color scheme preferred, attach the blades with their end brackets with all the screws and washers provided. Then mount the blades on the bottom side of fan motor with all the bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed on the motor to hold them separate from the rest from the kit hardware.
Tip: to hold the motor from becoming too off-level in this step, install the blades individually opposite to each other in the first place. 7. Install the lighting assembly. Attach the fan’s lighting assembly on the small round central housing unit just underneath the fan blades through the quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders in the order instructed. Note: a housing cap is provided if your lighting assembly is not wanted unconditionally. 8. Test the fan and lights. After turning the electricity back on, flip the wall switch to on. Set the pull-chain switches as desired. Often, the fan lighting is set to come on with all the wall switch, even though the fan itself is controlled from the pull-chain switch only, initially set in the off position. Note: The ceiling fan has a reversible motor switch which allows the draft either to go upward or downward as preferred. For more information on ceiling fan installation, begin to see the following sites.