Crystal Ceiling Fan Light Kit – Two good reasons to put in a ceiling fan, cooling and heating. If you live in a very cold climate, fans can push heated air gathered at the ceiling down again. Ceiling fans could be simple to install in case you have some mechanical aptitude. Current ceiling fans have remote-controls to vary speed and adjust lighting. If your room already has a permanent fixture inside ceiling, your permanent fixture probably has one hot or feed wire going to it, the neutral white and the bonding green or copper. Essentially this is the three-wire system. Many new construction homes have four wires available, one for the light the other for the fan motor control and the neutral and ground. If you simply have one Hot wire feeding the ceiling junction box, the remote-control fans work using your application. Additionally some remote-controlled fans use wall controller which sends its signal to the fan like a TV remote. It just seems like a wall control unit. If you really need the energy wire for your remote-controlled fan, please cap from the fourth wire which you will not need to use. This must be shown with your directions that included the fan assembly.
Once you might have acquired a fan you like, assemble it according to the instructions given. Some fans really are a little more complex, ask an associate to help if you need to. It is best to help it become assembled correctly, having a ceiling fan blade thud your self on the head could be annoying. Once you might have the pre-assembly completed, anyone can prepare the ceiling junction box. Of course I know you might have already made certain the energy to the ceiling box is deterred no one can possibly energize it accidentally. Once you might have succeeded in doing so, you must find three wires inside J-box. A copper or green wire for bonding. A white wire for the neutral plus a red or black wire for the power. If your junction box has a fourth wire, this could be setup for any wall controlled fan switch which can be great and allows you to use a non-remote wall controller. I should mention that some all fans have a wall controllers designed as remotes so avoid being confused because these all help the singular feed with your ceiling junction box.
A word about weight, not yours but anything about the size of your fan. If you might have a sizable fan and it is weighted near 12 pounds or more, you need a special junction box that could keep the excess weight. I would recommend you may ask someone who knows about these heavier fans if that’s what you are going to install. Most fans are lighter and could be positioned in most junction boxes without modifications.
Now let us get it down there, the fan which is. Many fans have a Hanger shaped like a U. Install this hanger on your box, the screws must be 8/32 types. That means a size 8 diameter or gauge screw with 32 threads per inch. Once you might have the hanger installed, get your fan motor without the blades installed and hang up it on the hanger. This allows you the electrician to get together the wires without struggling to juggle the motor and wire it as well. Connect the bonding wire to the chassis as noted inside instructions. Next connect the white neutral wire, and today the black wire. Swing the fan into place while using parts provided. Some have brackets, some utilize a metal plate and some use preformed mounting bases. Use your instructions and you will have a fan very quickly. Smaller fans may require you to pre-assemble your blades before hanging the fan. I always found installing the motor first and after that installing the blades last is easier. It does require however, you to work above your face to obtain the blades attached.
Once you might have the fan hanging, the blades installed and everything tightened anyone can step from the ladder, breathe deeply, then install the wall controller as provided. These all vary in design nonetheless they all follow similar procedures. Remember, you will have a line and load situation here. This means, the road side is the group of wires the feed in to the switch box through the panel whilst the Load side is going to your fan. This is critical so be sure you view the difference. Connect the Load side first: Connect your bonding wire first. Then connect your white neutral wire. Then your hot wire. Next do the Line (incoming) side next: Bond or ground should already be comprised to the new controller. Next wire your white neutral to the controllers neutral for the Line side. You may have already wired your neutrals together according to your instructions. Now wire your Hot or Power wire to the Line side of the controller. If you might have the fourth wire inside, cap it off or use it for the motor control and connect it accordingly to your directions. Red to Red is usually the case here. Once completed, get yourself some Iced Tea and luxuriate in your new fan.