Ceiling Fan 44 Inch – The flush-style ceiling fan is mounted snugly beside a designated horizontal fairly low ceiling where it’s off the beaten track, and from which it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, according to the room size being fitted, and may cost typically from $30 to $300. It generally has three fan motor speeds, which can be reversible. Except for the equipment and possible the rest essential for installing them, their self-assemble kits feature any devices. In many cases, the fan, that can have a unique lighting, will replace a ceiling fitting.
Safety, The electricity should be off once your there the place that the fan will be installed. If the fan is replacing a fitting, shut down its fuse or circuit breaker along with flipping its wall change to the off position. Stand on a sturdy wide-berth step stool or ladder during the installation; usually do not lean or enter a twisted position while there. Also, wear protective eye glasses or goggles. Furthermore, if additional auxiliary household wiring is needed, get professional advice or help first. Tools needed, instructions (electrical) eye glasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and further screws for securing the junction box, if required
Installation steps (after reading the fan installation instructions thoroughly). 1. Remove the fitting from your ceiling. With the electricity off, slowly get rid of the shade, bulbs, and fixture screws from your electrical junction box inside ceiling. Let the skeleton fixture hang there. With the light tester, ensure the wire connections to the fixture are cold (the exam light will always be off). Cut the wires, leaving 3-5″ of tail allowing you to connect the crooks to the ceiling fan motor assembly. If the house is old, only two wires might exist, a black one and a white one. Tip: also confirm the firmness of the electrical box inside ceiling. If it’s not solidly coupled to the ceiling, add two extra screws to its top side, which can require drilling two holes inside box for the kids. The ceiling fan is heavier than the fitting. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends of the tailing wires inside junction box cleanly, install the mounting bracket towards the box with all the two 5/32″ screw-bolts provided. Let the tailing wires hang outside of the bracket. 3. Hang the motor assembly from your bracket. Insert the topside motor-hanger in to the centralized holder of the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly really should swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one to the motor and a blue or off-color one to the lights to get attached below it. Overlap the stripped ends of the two wires (motor and lights) together with all the stripped end of the black ceiling wire inside box, and twist connect them together with all the wire nut provided. Connect the white assembly wire towards the white ceiling wire much the same way.
Then, to maintain these connections from loosening whilst the fan is working, tape the wide lower ends of the nuts on their wires with electrical tape. Also, attach the green fan wire (ground wire from your bracket frame) towards the electrical box when the box can also be grounded which has a third bare or green wire. Otherwise, when the electrical box in not grounded, ask a professional relating to this green wire connection. Some will say to get forced out be, i.e., do nothing at all by it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud towards the far ends of the mounting bracket with all the small screws provided. It covers/hides the sides of the motor and the wiring and ceiling box. 6. Assemble the fan blades (four to six) and mount them. After seeking the top or bottom reversible blade color scheme preferred, attach the blades on their end brackets with all the screws and washers provided. Then mount the blades towards the bottom side of fan motor with all the bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed towards the motor to maintain them separate from your rest of the kit hardware.
Tip: to maintain the motor from becoming too off-level in this step, install the blades one-by-one opposite together to begin with. 7. Install the lighting assembly. Attach the fan’s lighting assembly towards the small round central housing unit just beneath the fan blades through the quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders inside order instructed. Note: a housing cap is provided when the lighting assembly is not wanted without any reason. 8. Test the fan and lights. After turning the electricity back on, flip the wall change to on. Set the pull-chain switches as desired. Often, the fan lighting is set into the future on with all the wall switch, whilst the fan itself is controlled from the pull-chain switch only, initially set inside off position. Note: The ceiling fan has a reversible motor switch which allows the draft either to go upward or downward as preferred. For more information on ceiling fan installation, start to see the following sites.