Beach Ceiling Fans – Two top reasons to install a ceiling fan, heating and cooling. If you live in a cold climate, fans can push warm air gathered nearby the ceiling back off. Ceiling fans could be easy to install if you have some mechanical aptitude. Current ceiling fans feature remote-controls to vary speed and adjust lighting. If your room already includes a light fixture in the ceiling, your light fixture probably has one hot or feed wire gonna it, the neutral white and the bonding green or copper. Essentially this is the three-wire system. Many new construction homes have four wires available, one for that light and something for that fan motor control and the neutral and ground. If you simply have one Hot wire feeding the ceiling junction box, the remote-control fans will work together with your application. Additionally some remote-controlled fans use wall controller which sends its signal to the fan just like a TV remote. It just looks like a wall control unit. If you just have the power wire on your remote-controlled fan, please cap over fourth wire which you will not want to utilize. This needs to be shown with your directions that came with the fan assembly.
Once you might have acquired a fan that suits you, build it according to the instructions given. Some fans really are a bit more complex, ask an associate to assist if necessary. It is best to help it become assembled correctly, using a ceiling fan blade thud yourself on the head could be annoying. Once you might have the pre-assembly completed, you can now prepare the ceiling junction box. Of course I know you might have already ensured the power to the ceiling box is powered down and no you can energize it accidentally. Once you might have done this, you should find three wires in the J-box. A copper or green wire for bonding. A white wire for that neutral plus a red or black wire for that power. If your junction box includes a fourth wire, this would be setup to get a wall controlled fan switch which is great and allows you to utilize a non-remote wall controller. I should mention that some all fans feature a wall controllers designed as remotes so you shouldn’t be confused because these all assist the singular feed with your ceiling junction box.
A word about weight, not yours but anything about the height and width of your fan. If you might have a big fan and its weighted near 12 pounds or maybe more, you might need a special junction box that will secure the additional weight. I would recommend you may ask someone who knows about these heavier fans if that is what you’re gonna install. Most fans are lighter and could be set up in most junction boxes without modifications.
Now let us get it there, the fan that is certainly. Many fans feature a Hanger shaped like a U. Install this hanger on to your box, the screws needs to be 8/32 types. That means a size 8 diameter or gauge screw with 32 threads per inch. Once you might have the hanger installed, grab your fan motor without the blades installed and place it on the hanger. This allows you the electrician to connect the wires without struggling to juggle the motor and wire it simultaneously. Connect the bonding wire to the chassis as noted in the instructions. Next connect the white neutral wire, and after this the black wire. Swing the fan into place while using parts provided. Some have brackets, some work with a metal plate while some use preformed mounting bases. Use your instructions and you will have a fan right away. Smaller fans may need that you pre-assemble your blades before hanging the fan. I always found installing the motor first after which installing the blades last is easier. It does require however, that you work above your mind to obtain the blades attached.
Once you might have the fan hanging, the blades installed and everything tightened you can now step over ladder, take a deep breath, then install the wall controller as provided. These all vary in design however they all follow similar procedures. Remember, you will find a line and load situation here. This means, the line side will be the set of wires the feed in to the switch box through the panel even though the Load side is gonna your fan. This is critical so make sure you see the difference. Connect the Load side first: Connect your bonding wire first. Then connect your white neutral wire. Then your hot wire. Next perform Line (incoming) side next: Bond or ground should already be constructed to the new controller. Next wire your white neutral to the controllers neutral for that Line side. You may have already wired your neutrals together based on your instructions. Now wire your Hot or Power wire to the Line side of your respective controller. If you might have the fourth wire within, cap it well or use it for that motor control and connect it accordingly for your directions. Red to Red is truly the case here. Once completed, be some Iced Tea and get your fan.