Savoy Ceiling Fans – The flush-style ceiling fan is mounted snugly alongside an appartment horizontal fairly low ceiling where it can be off the beaten track, and from which it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, with regards to the room size being fitted, and may cost typically from $30 to $300. It generally has three fan motor speeds, that happen to be reversible. Except for the equipment and possible other regions needed for installing them, their self-assemble kits feature the rest. In many cases, the fan, that will have its own lighting, will replace a ceiling permanent fixture.
Safety, The electricity should be off at the site where the fan is usually to be installed. If the fan is replacing a permanent fixture, power down its fuse or circuit breaker in addition to flipping its wall switch the signal from the off position. Stand on a sturdy wide-berth step stool or ladder in the installation; tend not to lean or get into a twisted position while there. Also, wear protective eye glasses or goggles. Furthermore, if additional auxiliary household wiring should be used, get professional advice or help first. Tools needed, instructions (electrical) eye glasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and further screws for securing the junction box, as appropriate
Installation steps (after reading the fan installation instructions thoroughly). 1. Remove the permanent fixture from the ceiling. With the electricity off, slowly get rid of the shade, bulbs, and fixture screws from the electrical junction box in the ceiling. Let the skeleton fixture hang there. With the light tester, ensure that the wire connections to the fixture are cold (the exam light will stay off). Cut the wires, leaving 3-5″ of tail allowing you to connect them to the ceiling fan motor assembly. If the home is old, only two wires might exist, a black one as well as a white one. Tip: also check the firmness with the electrical box in the ceiling. If it can be not solidly attached to the ceiling, add two extra screws to its top side, which might require drilling two holes in the box on their behalf. The ceiling fan is heavier compared to the permanent fixture. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends with the tailing wires in the junction box cleanly, install the mounting bracket towards the box with all the two 5/32″ screw-bolts provided. Let the tailing wires hang outside with the bracket. 3. Hang the motor assembly from the bracket. Insert the topside motor-hanger in to the centralized holder with the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly is supposed to swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one for your motor as well as a blue or off-color one for your lights to get attached below it. Overlap the stripped ends of these two wires (motor and lights) together with all the stripped end with the black ceiling wire in the box, and twist connect them together with all the wire nut provided. Connect the white assembly wire towards the white ceiling wire exactly the same way.
Then, to keep these connections from loosening as the fan is working, tape the wide lower ends of these nuts to their wires with electrical tape. Also, attach the green fan wire (ground wire from the bracket frame) towards the electrical box if your box is also grounded having a third bare or green wire. Otherwise, if your electrical box in not grounded, ask a professional about this green wire connection. Some will say to let it sit be, i.e., relax from it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud towards the far ends with the mounting bracket with all the small screws provided. It covers/hides the sides with the motor and the wiring and ceiling box. 6. Assemble the fan blades (3 to 5) and mount them. After choosing the top or bottom reversible blade color scheme preferred, attach the blades to their end brackets with all the screws and washers provided. Then mount the blades towards the bottom side of fan motor with all the bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed towards the motor to keep them separate from the rest with the kit hardware.
Tip: to keep the motor from becoming too off-level during this step, install the blades one by one opposite to each other first of all. 7. Install the lighting assembly. Attach the fan’s lighting assembly towards the small round central housing unit just below the fan blades through the quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders in the order instructed. Note: a housing cap is provided if your lighting assembly is not wanted at all. 8. Test the fan and lights. After turning the electricity back on, flip the wall switch the signal from on. Set the pull-chain switches as desired. Often, the fan lighting is set into the future on with all the wall switch, as the fan itself is controlled with the pull-chain switch only, initially set in the off position. Note: The ceiling fan includes a reversible motor switch that permits the draft either to go upward or downward as preferred. For more information on ceiling fan installation, start to see the following sites.