Wiring A Ceiling Fan With 2 Switches – The flush-style ceiling fan is mounted snugly close to a set horizontal fairly low ceiling where it’s taken care of, and where it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, with respect to the size of the room being fitted, and may cost typically from $30 to $300. It generally has three fan motor speeds, that happen to be reversible. Except for the tools and possible other areas needed for installing them, their self-assemble kits feature anything else. In many cases, the fan, that will have its own lighting, will replace a ceiling permanent fixture.
Safety, The electricity must be off at the site the place that the fan will be installed. If the fan is replacing a permanent fixture, de-activate its fuse or circuit breaker together with flipping its wall switch to the off position. Stand on a sturdy wide-berth step stool or ladder during the installation; do not lean or get into a twisted position while there. Also, wear protective eyeglasses or goggles. Furthermore, if additional auxiliary household wiring should be used, get professional advice or help first. Tools needed, instructions (electrical) eyeglasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and extra screws for securing the junction box, as appropriate
Installation steps (reading the fan installation instructions thoroughly). 1. Remove the permanent fixture in the ceiling. With the electricity off, slowly remove the shade, bulbs, and fixture screws in the electrical junction box inside ceiling. Let the skeleton fixture hang there. With the light tester, ensure that the wire connections to the fixture are cold (test light will stay off). Cut the wires, leaving 3-5″ of tail in order to connect the crooks to the ceiling fan motor assembly. If the house is old, only two wires might exist, a black one and a white one. Tip: also look at the firmness in the electrical box inside ceiling. If it’s not solidly connected to the ceiling, add two extra screws to its top side, which could require drilling two holes inside box for the kids. The ceiling fan is heavier compared to the permanent fixture. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends in the tailing wires inside junction box cleanly, install the mounting bracket on the box with all the two 5/32″ screw-bolts provided. Let the tailing wires hang outside in the bracket. 3. Hang the motor assembly in the bracket. Insert the topside motor-hanger into the centralized holder in the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly really should swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one for your motor and a blue or off-color one for your lights to be attached below it. Overlap the stripped ends of such two wires (motor and lights) together with all the stripped end in the black ceiling wire inside box, and twist connect them together with all the wire nut provided. Connect the white assembly wire on the white ceiling wire much the same way.
Then, to help keep these connections from loosening as the fan is working, tape the wide lower ends of such nuts for their wires with electrical tape. Also, attach the green fan wire (ground wire in the bracket frame) on the electrical box when the box can also be grounded using a third bare or green wire. Otherwise, when the electrical box in not grounded, ask an experienced concerning this green wire connection. Some will say to let it sit be, i.e., relax with it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud on the far ends in the mounting bracket with all the small screws provided. It covers/hides the sides in the motor along with the wiring and ceiling box. 6. Assemble the fan blades (3 to 4) and mount them. After seeking the top or bottom reversible blade color scheme preferred, attach the blades for their end brackets with all the screws and washers provided. Then mount the blades on the bottom side of fan motor with all the bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed on the motor to help keep them separate in the rest in the kit hardware.
Tip: to help keep the motor from becoming too off-level in this step, install the blades one by one opposite together to start with. 7. Install the lighting assembly. Attach the fan’s lighting assembly on the small round central housing unit just beneath the fan blades through quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders inside order instructed. Note: a housing cap is provided when the lighting assembly is just not wanted at all. 8. Test the fan and lights. After turning the electricity back on, flip the wall switch to on. Set the pull-chain switches as desired. Often, the fan lighting is set ahead on with all the wall switch, as the fan itself is controlled through the pull-chain switch only, initially set inside off position. Note: The ceiling fan has a reversible motor switch that allows the draft either to go upward or downward as preferred. For more information on ceiling fan installation, understand the following sites.