Black Flush Mount Ceiling Fan – The flush-style ceiling fan is mounted snugly alongside a designated horizontal fairly low ceiling where it’s taken care of, and from which it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, according to the room size being fitted, and may cost typically from $30 to $300. It generally has three fan motor speeds, which are reversible. Except for the various tools and possible the rest needed for installing them, their self-assemble kits feature anything else. In many cases, the fan, which will have a unique lighting, will replace a ceiling permanent fixture.
Safety, The electricity has to be off once your there where the fan will be installed. If the fan is replacing a permanent fixture, de-activate its fuse or circuit breaker as well as flipping its wall change to the off position. Stand on a sturdy wide-berth step stool or ladder in the installation; don’t lean or get into a twisted position while there. Also, wear protective eyeglasses or goggles. Furthermore, if additional auxiliary household wiring is required, get professional advice or help first. Tools needed, instructions (electrical) eyeglasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and further screws for securing the junction box, if needed
Installation steps (seeing the fan installation instructions thoroughly). 1. Remove the permanent fixture from your ceiling. With the electricity off, slowly get rid of the shade, bulbs, and fixture screws from your electrical junction box in the ceiling. Let the skeleton fixture hang there. With the light tester, guarantee the wire connections to this particular fixture are cold (the test light will stay off). Cut the wires, leaving 3-5″ of tail to get in touch these phones the ceiling fan motor assembly. If the property is old, only two wires might exist, a black one along with a white one. Tip: also look into the firmness of the electrical box in the ceiling. If it’s not solidly connected to the ceiling, add two extra screws to its top side, which might require drilling two holes in the box for the children. The ceiling fan is heavier than the permanent fixture. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends of the tailing wires in the junction box cleanly, install the mounting bracket on the box while using two 5/32″ screw-bolts provided. Let the tailing wires hang outside of the bracket. 3. Hang the motor assembly from your bracket. Insert the topside motor-hanger to the centralized holder of the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly should really swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one for your motor along with a blue or off-color one for your lights to be attached below it. Overlap the stripped ends of those two wires (motor and lights) together while using stripped end of the black ceiling wire in the box, and twist connect them together while using wire nut provided. Connect the white assembly wire on the white ceiling wire exactly the same.
Then, to keep these connections from loosening whilst the fan is working, tape the wide lower ends of those nuts for their wires with electrical tape. Also, attach the green fan wire (ground wire from your bracket frame) on the electrical box if the box can also be grounded with a third bare or green wire. Otherwise, if the electrical box in not grounded, ask an experienced relating to this green wire connection. Some will say to leave it be, i.e., do nothing at all with it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud on the far ends of the mounting bracket while using small screws provided. It covers/hides the sides of the motor and also the wiring and ceiling box. 6. Assemble the fan blades (3 to 5) and mount them. After picking out the top or bottom reversible blade color scheme preferred, attach the blades for their end brackets while using screws and washers provided. Then mount the blades on the bottom side of fan motor while using bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed on the motor to keep them separate from your rest of the kit hardware.
Tip: to keep the motor from becoming too off-level during this step, install the blades individually opposite to each other to start with. 7. Install the lighting assembly. Attach the fan’s lighting assembly on the small round central housing unit just under the fan blades via the quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders in the order instructed. Note: a housing cap is provided if the lighting assembly is just not wanted for any reason. 8. Test the fan and lights. After turning the electricity back on, flip the wall change to on. Set the pull-chain switches as desired. Often, the fan lighting is set to come on while using wall switch, whilst the fan itself is controlled with the pull-chain switch only, initially set in the off position. Note: The ceiling fan carries a reversible motor switch that enables the draft either to go upward or downward as preferred. For more information on ceiling fan installation, begin to see the following sites.