Ceiling Fan Box – The flush-style ceiling fan is mounted snugly next to a set horizontal fairly low ceiling where it can be out of the way, and from where it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, with respect to the size of the room being fitted, and can cost typically from $30 to $300. It generally has three fan motor speeds, that are reversible. Except for the tools and possible other parts necessary for installing them, their self-assemble kits feature the rest. In many cases, the fan, that may have a unique lighting, will replace a ceiling permanent fixture.
Safety, The electricity have to be off at the site the location where the fan is to be installed. If the fan is replacing a permanent fixture, shut down its fuse or circuit breaker along with flipping its wall switch to the off position. Stand on a sturdy wide-berth step stool or ladder in the installation; don’t lean or enter into a twisted position while there. Also, wear protective eye glasses or goggles. Furthermore, if additional auxiliary household wiring is necessary, get professional advice or help first. Tools needed, instructions (electrical) eye glasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and further screws for securing the junction box, as appropriate
Installation steps (seeing the fan installation instructions thoroughly). 1. Remove the permanent fixture through the ceiling. With the electricity off, slowly eliminate the shade, bulbs, and fixture screws through the electrical junction box inside ceiling. Let the skeleton fixture hang there. With the light tester, ensure the wire connections to this fixture are cold (quality light will remain off). Cut the wires, leaving 3-5″ of tail allowing you to connect the crooks to the ceiling fan motor assembly. If the property is old, only two wires might exist, a black one plus a white one. Tip: also confirm the firmness from the electrical box inside ceiling. If it can be not solidly connected to the ceiling, add two extra screws to its top side, which could require drilling two holes inside box for them. The ceiling fan is heavier compared to permanent fixture. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends from the tailing wires inside junction box cleanly, install the mounting bracket to the box with all the two 5/32″ screw-bolts provided. Let the tailing wires hang outside from the bracket. 3. Hang the motor assembly through the bracket. Insert the topside motor-hanger to the centralized holder from the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly should really swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one for the motor plus a blue or off-color one for the lights being attached below it. Overlap the stripped ends of these two wires (motor and lights) together with all the stripped end from the black ceiling wire inside box, and twist connect them together with all the wire nut provided. Connect the white assembly wire to the white ceiling wire exactly the same way.
Then, to keep these connections from loosening even though the fan is working, tape the wide lower ends of these nuts to their wires with electrical tape. Also, attach the green fan wire (ground wire through the bracket frame) to the electrical box if your box can also be grounded which has a third bare or green wire. Otherwise, if your electrical box in not grounded, ask a specialist about this green wire connection. Some will say to get forced out be, i.e., do nothing with it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud to the far ends from the mounting bracket with all the small screws provided. It covers/hides the perimeters from the motor and also the wiring and ceiling box. 6. Assemble the fan blades (four to six) and mount them. After seeking the top or bottom reversible blade color scheme preferred, attach the blades to their end brackets with all the screws and washers provided. Then mount the blades to the bottom side of fan motor with all the bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed to the motor to keep them separate through the rest from the kit hardware.
Tip: to keep the motor from becoming too off-level during this step, install the blades one at a time opposite together to begin with. 7. Install the lighting assembly. Attach the fan’s lighting assembly to the small round central housing unit just underneath the fan blades through quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders inside order instructed. Note: a housing cap is provided if your lighting assembly isn’t wanted at all. 8. Test the fan and lights. After turning the electricity back on, flip the wall switch to on. Set the pull-chain switches as desired. Often, the fan lighting is set ahead on with all the wall switch, even though the fan itself is controlled with the pull-chain switch only, initially set inside off position. Note: The ceiling fan includes a reversible motor switch that allows the draft either to go upward or downward as preferred. For more information on ceiling fan installation, understand the following sites.