Harbor Breeze Ceiling Fan Switch – The flush-style ceiling fan is mounted snugly beside a designated horizontal fairly low ceiling where it really is out of the way, and from which it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, with respect to the size of room being fitted, which enable it to cost typically from $30 to $300. It generally has three fan motor speeds, which are reversible. Except for the equipment and possible other areas required for installing them, their self-assemble kits have anything else. In many cases, the fan, which will have its very own lighting, will replace a ceiling permanent fixture.
Safety, The electricity must be off to begin the location where the fan is usually to be installed. If the fan is replacing a permanent fixture, shut down its fuse or circuit breaker along with flipping its wall exchange signal of the off position. Stand on a sturdy wide-berth step stool or ladder throughout the installation; usually do not lean or enter a twisted position while there. Also, wear protective eye glasses or goggles. Furthermore, if additional auxiliary household wiring is necessary, get professional advice or help first. Tools needed, instructions (electrical) eye glasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and extra screws for securing the junction box, if required
Installation steps (looking at the fan installation instructions thoroughly). 1. Remove the permanent fixture through the ceiling. With the electricity off, slowly remove the shade, bulbs, and fixture screws through the electrical junction box inside the ceiling. Let the skeleton fixture hang there. With the light tester, guarantee the wire connections for this fixture are cold (quality light will remain off). Cut the wires, leaving 3-5″ of tail in order to connect these to the ceiling fan motor assembly. If the residence is old, only two wires might exist, a black one as well as a white one. Tip: also look into the firmness from the electrical box inside the ceiling. If it really is not solidly coupled to the ceiling, add two extra screws to its top side, which can require drilling two holes inside the box for the children. The ceiling fan is heavier as opposed to permanent fixture. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends from the tailing wires inside the junction box cleanly, install the mounting bracket to the box with all the two 5/32″ screw-bolts provided. Let the tailing wires hang outside from the bracket. 3. Hang the motor assembly through the bracket. Insert the topside motor-hanger to the centralized holder from the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly is supposed to swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one to the motor as well as a blue or off-color one to the lights to become attached below it. Overlap the stripped ends of those two wires (motor and lights) together with all the stripped end from the black ceiling wire inside the box, and twist connect them together with all the wire nut provided. Connect the white assembly wire to the white ceiling wire exactly the same way.
Then, to keep these connections from loosening even though the fan is working, tape the wide lower ends of those nuts on their wires with electrical tape. Also, attach the green fan wire (ground wire through the bracket frame) to the electrical box when the box is also grounded using a third bare or green wire. Otherwise, when the electrical box in not grounded, ask a professional about this green wire connection. Some will say to leave it be, i.e., relax from it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud to the far ends from the mounting bracket with all the small screws provided. It covers/hides the sides from the motor and also the wiring and ceiling box. 6. Assemble the fan blades (four to six) and mount them. After picking out the top or bottom reversible blade color scheme preferred, attach the blades on their end brackets with all the screws and washers provided. Then mount the blades to the bottom side of fan motor with all the bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed to the motor to keep them separate through the rest from the kit hardware.
Tip: to keep the motor from becoming too off-level during this step, install the blades one at a time opposite to each other in the first place. 7. Install the lighting assembly. Attach the fan’s lighting assembly to the small round central housing unit just under the fan blades through quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders inside the order instructed. Note: a housing cap is provided when the lighting assembly isn’t wanted at all. 8. Test the fan and lights. After turning the electricity back on, flip the wall exchange signal of on. Set the pull-chain switches as desired. Often, the fan lighting is set ahead on with all the wall switch, even though the fan itself is controlled with the pull-chain switch only, initially set inside the off position. Note: The ceiling fan features a reversible motor switch that permits the draft either to go upward or downward as preferred. For more information on ceiling fan installation, start to see the following sites.