36 Inch Ceiling Fan With Light – The flush-style ceiling fan is mounted snugly alongside a flat horizontal fairly low ceiling where it is taken care of, and from which it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, with respect to the room size being fitted, and may cost typically from $30 to $300. It generally has three fan motor speeds, that happen to be reversible. Except for the instruments and possible the rest essential for installing them, their self-assemble kits feature everything else. In many cases, the fan, which will have its own lighting, will replace a ceiling light fixture.
Safety, The electricity must be off to begin the location where the fan is usually to be installed. If the fan is replacing a light fixture, de-activate its fuse or circuit breaker together with flipping its wall switch the signal from the off position. Stand on a sturdy wide-berth step stool or ladder throughout the installation; tend not to lean or end up in a twisted position while there. Also, wear protective eyeglasses or goggles. Furthermore, if additional auxiliary household wiring is needed, get professional advice or help first. Tools needed, instructions (electrical) eyeglasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and additional screws for securing the junction box, if needed
Installation steps (looking at the fan installation instructions thoroughly). 1. Remove the light fixture from your ceiling. With the electricity off, slowly eliminate the shade, bulbs, and fixture screws from your electrical junction box in the ceiling. Let the skeleton fixture hang there. With the light tester, guarantee the wire connections to this particular fixture are cold (the exam light will continue to be off). Cut the wires, leaving 3-5″ of tail in order to connect them to the ceiling fan motor assembly. If the house is old, only two wires might exist, a black one plus a white one. Tip: also check the firmness with the electrical box in the ceiling. If it is not solidly coupled to the ceiling, add two extra screws to its top side, which might require drilling two holes in the box for the children. The ceiling fan is heavier as opposed to light fixture. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends with the tailing wires in the junction box cleanly, install the mounting bracket for the box using the two 5/32″ screw-bolts provided. Let the tailing wires hang outside with the bracket. 3. Hang the motor assembly from your bracket. Insert the topside motor-hanger in to the centralized holder with the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly should really swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one for that motor plus a blue or off-color one for that lights to get attached below it. Overlap the stripped ends of such two wires (motor and lights) together using the stripped end with the black ceiling wire in the box, and twist connect them together using the wire nut provided. Connect the white assembly wire for the white ceiling wire exactly the same way.
Then, to hold these connections from loosening as the fan is working, tape the wide lower ends of such nuts for their wires with electrical tape. Also, attach the green fan wire (ground wire from your bracket frame) for the electrical box when the box is additionally grounded with a third bare or green wire. Otherwise, when the electrical box in not grounded, ask an experienced relating to this green wire connection. Some will say to leave it be, i.e., do nothing at all by using it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud for the far ends with the mounting bracket using the small screws provided. It covers/hides the edges with the motor and also the wiring and ceiling box. 6. Assemble the fan blades (3 to 5) and mount them. After picking out the top or bottom reversible blade color scheme preferred, attach the blades for their end brackets using the screws and washers provided. Then mount the blades for the bottom side of fan motor using the bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed for the motor to hold them separate from your rest with the kit hardware.
Tip: to hold the motor from becoming too off-level within this step, install the blades one-by-one opposite to one another in the first place. 7. Install the lighting assembly. Attach the fan’s lighting assembly for the small round central housing unit just below the fan blades using the quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders in the order instructed. Note: a housing cap is provided when the lighting assembly just isn’t wanted for any reason. 8. Test the fan and lights. After turning the electricity back on, flip the wall switch the signal from on. Set the pull-chain switches as desired. Often, the fan lighting is set in the future on using the wall switch, as the fan itself is controlled by the pull-chain switch only, initially set in the off position. Note: The ceiling fan includes a reversible motor switch that enables the draft either to go upward or downward as preferred. For more information on ceiling fan installation, begin to see the following sites.