Pink Ceiling Fan – The flush-style ceiling fan is mounted snugly next to an appartment horizontal fairly low ceiling where it really is taken care of, and from which it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, according to the size of room being fitted, which enable it to cost typically from $30 to $300. It generally has three fan motor speeds, which can be reversible. Except for the equipment and possible other parts needed for installing them, their self-assemble kits include the rest. In many cases, the fan, that may have its own lighting, will replace a ceiling permanent fixture.
Safety, The electricity must be off to begin the place that the fan shall be installed. If the fan is replacing a permanent fixture, power down its fuse or circuit breaker as well as flipping its wall switch to the off position. Stand on a sturdy wide-berth step stool or ladder through the installation; tend not to lean or enter into a twisted position while there. Also, wear protective eye glasses or goggles. Furthermore, if additional auxiliary household wiring should be used, get professional advice or help first. Tools needed, instructions (electrical) eye glasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and further screws for securing the junction box, if needed
Installation steps (seeing the fan installation instructions thoroughly). 1. Remove the permanent fixture in the ceiling. With the electricity off, slowly take away the shade, bulbs, and fixture screws in the electrical junction box within the ceiling. Let the skeleton fixture hang there. With the light tester, make sure the wire connections for this fixture are cold (quality light will stay off). Cut the wires, leaving 3-5″ of tail for connecting these phones the ceiling fan motor assembly. If the home is old, only two wires might exist, a black one plus a white one. Tip: also confirm the firmness in the electrical box within the ceiling. If it really is not solidly connected to the ceiling, add two extra screws to its top side, which might require drilling two holes within the box for the kids. The ceiling fan is heavier compared to the permanent fixture. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends in the tailing wires within the junction box cleanly, install the mounting bracket for the box with all the two 5/32″ screw-bolts provided. Let the tailing wires hang outside in the bracket. 3. Hang the motor assembly in the bracket. Insert the topside motor-hanger in to the centralized holder in the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly should really swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one for the motor plus a blue or off-color one for the lights being attached below it. Overlap the stripped ends of these two wires (motor and lights) together with all the stripped end in the black ceiling wire within the box, and twist connect them together with all the wire nut provided. Connect the white assembly wire for the white ceiling wire the same way.
Then, to hold these connections from loosening while the fan is working, tape the wide lower ends of these nuts on their wires with electrical tape. Also, attach the green fan wire (ground wire in the bracket frame) for the electrical box if your box is additionally grounded which has a third bare or green wire. Otherwise, if your electrical box in not grounded, ask a professional about this green wire connection. Some will say to leave it be, i.e., do nothing at all from it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud for the far ends in the mounting bracket with all the small screws provided. It covers/hides the sides in the motor and also the wiring and ceiling box. 6. Assemble the fan blades (3 to 4) and mount them. After deciding on the top or bottom reversible blade color scheme preferred, attach the blades on their end brackets with all the screws and washers provided. Then mount the blades for the bottom side of fan motor with all the bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed for the motor to hold them separate in the rest in the kit hardware.
Tip: to hold the motor from becoming too off-level with this step, install the blades one at a time opposite to each other in the first place. 7. Install the lighting assembly. Attach the fan’s lighting assembly for the small round central housing unit just underneath the fan blades through the quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders within the order instructed. Note: a housing cap is provided if your lighting assembly is not wanted for any reason. 8. Test the fan and lights. After turning the electricity back on, flip the wall switch to on. Set the pull-chain switches as desired. Often, the fan lighting is set into the future on with all the wall switch, while the fan itself is controlled with the pull-chain switch only, initially set within the off position. Note: The ceiling fan features a reversible motor switch which allows the draft either to go upward or downward as preferred. For more information on ceiling fan installation, see the following sites.