Outdoor Deck Floor Mats – Let’s begin first we must assess the area can it be a turf or concrete base within the decking a turf base will need to be dug off and membrane put within the decking you are able to and really should put membrane under any decking project to avoid any weeds penetrating through, where would be the damp course levels as we don’t want when over the damp course ideally when needs to be two bricks below the damp course. And will there be any drain access points within the decking since these will require a special decking drain cover. Always remember the decking boards go horizontal along the home. Always remember decking higher that 1.2m over walk out will require planning permission
Now we now have assessed these factors they will decide the height of when and any special requirements that need to be incorporated in the decking project. Estimation of materials first look at the area in the decking i.e 4.8m x 4.8m = 23.04sq meters. Then use this equation to calculate the decking boards needed 4800mm / 140mm (deck board width that are 4.8m long) = 35 decking boards. Add a little for cuts and edges that need to be filled in. Then calculate the strain bearing supports (4 x 2 pressure treated CLS) 4800 / 600 = 8 This the amount of horizontal 4 x 2 pieces needed for the internal structure in the decking in addition to the outside in the frame i.e. 4800 x 4 = 19.2m + (8 x 4800) = 58m of four years old x 2. Add some for the cross member struts and positioning pegs (banged and concreted if required in the ground) about three to four 4.8m lengths should suffice.
Establishing the frame this should be done near or as close for the position in the final deck. Start by cutting the ends in the required wood square this may help using the construction in the frame always cut the components of wood a similar length since the frame should never be square in the event the wood is of different lengths. Then join the corners in the frame by piloting the holes for the 4 inch screws to get screwed into wood. Once this can be done you should have the frame square, utilizing an engineers square place it a single corner and move until square. Then screw a batten within the corner to support the corner square try this for all corners. Then measure internally from the horizontal in the frame where the load bearers are inclined divide this measurement by 600mm this can give you the same spacing for the struts. Next screw theses in place it is much easier to place a amount of wood within the frame while carrying this out to get the edges to satisfy. Once this can be done look at the cross member struts three feet is about right for the spacing of these. They go vertically along when frame stepping out then directly into enable screwing.
Ranking of when, get when into position using the help of your friend. Then start within the highest corner of when and bang a bit of cut 4 x 2 (depending about the height of when cut accordingly) in the ground with a large sledge hammer. Once done lift when into position and screw together with a 4 inch screw. Now work along when for the next horizontal corner lifts the corner so the frame is level and do a similar. Now work down the front possess a slight lean away from the house or be sure whichever way the boards are running tip when so the water runs out in the surface. Then work your way across when ensuring that any weak spot is based on banging a piece of four years old x 2 in the ground beneath it. Once this can be done test the strength by walking down the struts to demonstrate any weak spot don’t be concerned a lot of since the decking boards will strengthen the decking after they are fixed for the frame.
Today we cut and suit the decking boards for the frame. Make sure all the edges in the decking are cut square before cutting for the correct length. This will aid construction and overall Finnish in the decking project. Start with a full amount of decking ensuring the final meets the frame or cut the board for the nearest beam and fasten the board with a Paslode nail gun using 50mm nails or pilot and countersink holes and screw the boards screwing is way better long lasting but nailing is faster and easier. Work along when spacing with a 5mm nail banged in a piece of four years old x 2, this can ensure that this gap remains a similar. Always remember to stagger the joints in the decking another board so the joints blend in the decking. Once you decking boards are fitted then fit any surrounding decking boards for the edges to hide up any in the frame work and check for virtually any boards which have splinters and sand these down if you are able to.