Solar Deck Rail Lights – Why don’t we begin first we must appraise the area can it be a turf or concrete base beneath the decking a turf base will should be dug off and membrane put beneath the decking you can and will put membrane under any decking project to stop any weeds penetrating through, where will be the damp course levels once we don’t want occasions over the damp course ideally occasions needs to be two bricks below the damp course. And will there be any drain access points beneath the decking because these need a special decking drain cover. Always remember the decking boards go horizontal along your house. Always remember decking higher that 1.2m over walk out need planning permission
Now we’ve assessed these factors they’ll decide the height of occasions and then any special requirements that should be incorporated into the decking project. Estimation of materials first measure the area of the decking i.e 4.8m x 4.8m = 23.04sq meters. Then use this equation to calculate the decking boards needed 4800mm / 140mm (deck board width that happen to be 4.8m long) = 35 decking boards. Add a little for cuts and edges that should be filled in. Then calculate the load bearing supports (4 x 2 pressure treated CLS) 4800 / 600 = 8 This the volume of horizontal 4 x 2 pieces needed for your internal structure of the decking together with outside of the frame i.e. 4800 x 4 = 19.2m + (8 x 4800) = 58m of four x 2. Add some for your cross member struts and positioning pegs (banged and concreted as needed into the ground) about three to four 4.8m lengths should suffice.
Setting up the frame this should be done near or as close on the position of the final deck. Start by cutting the ends of the required wood square this can help using the construction of the frame always cut the pieces of wood the same length since the frame will not be square if your wood is of different lengths. Then join the corners of the frame by piloting the holes for your 4 inch screws being screwed into wood. Once this can be done you’ll want to obtain the frame square, utilizing an engineers square put it a single corner and move until square. Then screw a batten inside the corner to carry the corner square do that for many corners. Then measure internally from your horizontal of the frame where the load bearers are inclined divide this measurement by 600mm this may present you with an identical spacing for your struts. Next screw theses in position it is much easier to place a length of wood beneath the frame while carrying this out to obtain the edges to fulfill. Once this can be done measure the cross member struts three feet is around right for your spacing of such. They go vertically along occasions frame stepping out then directly into enable screwing.
Location of occasions, get occasions into position using the help of the friend. Then start inside the highest corner of occasions and bang a piece of cut 4 x 2 (depending about the height of occasions cut accordingly) into the ground with a large sledge hammer. Once done lift occasions into position and screw together with a 4 inch screw. Now work along occasions on the next horizontal corner lifts the corner and so the frame is level and do the same. Now work down the front use a slight lean away from your house or ensure whichever way the boards are running tip occasions and so the water runs out of the surface. Then work your way across occasions making certain that any weak point is backed up by banging a piece of four x 2 into the ground beneath it. Once this can be done test the strength by walking down the struts to exhibit any weak point no problem too much since the decking boards will strengthen the decking once they are fixed on the frame.
Today we cut and fit in the decking boards on the frame. Make sure all of the edges of the decking are cut square before cutting on the correct length. This will aid construction and overall Finnish of the decking project. Start with a full length of decking making certain the final meets the frame or cut the board on the nearest beam and fix the board with a Paslode nail gun using 50mm nails or pilot and countersink holes and screw the boards screwing is best lasting but nailing is faster and simpler. Work along occasions spacing with a 5mm nail banged in to a piece of four x 2, this may ensure how the gap remains the same. Always remember to stagger the joints of the decking every other board and so the joints blend into the decking. Once you decking boards are fitted then fit any surrounding decking boards on the edges to pay for up any of the frame work and check for just about any boards which may have splinters and sand these down if you can.