Flipping Pressure Treated Deck Boards – Why don’t we begin first we must measure the area can it be a turf or concrete base beneath the decking a turf base will need to be dug off and membrane put beneath the decking you can and may put membrane under any decking project to avoid any weeds penetrating through, where will be the damp course levels even as we are afraid those times across the damp course ideally those times ought to be two bricks below the damp course. And can there be any drain access points beneath the decking as these need a special decking drain cover. Always remember the decking boards go horizontal along the house. Always remember decking higher that 1.2m off the ground level need planning permission
Now we now have assessed these factors they are going to decide the height of those times and then for any special requirements that need to be incorporated into the decking project. Estimation of materials first measure the area with the decking i.e 4.8m x 4.8m = 23.04sq meters. Then employ this equation to calculate the decking boards needed 4800mm / 140mm (deck board width that are 4.8m long) = 35 decking boards. Add a little for cuts and edges that need to be filled in. Then calculate the stress bearing supports (4 x 2 pressure treated CLS) 4800 / 600 = 8 This the volume of horizontal 4 x 2 pieces needed for the internal structure with the decking plus the outside with the frame i.e. 4800 x 4 = 19.2m + (8 x 4800) = 58m of four x 2. Add some for the cross member struts and positioning pegs (banged and concreted if required into the ground) about three or four 4.8m lengths should suffice.
Establishing the frame this ought to be done near or as close on the position with the final deck. Start by cutting the ends with the required wood square this will help using the construction with the frame always cut the components of wood the identical length because frame will never be square if the wood is of different lengths. Then join the corners with the frame by piloting the holes for the 4 inch screws to be screwed into wood. Once this is done you need to get the frame square, utilizing an engineers square put it a single corner and move until square. Then screw a batten inside corner to keep the corner square do this for many corners. Then measure internally in the horizontal with the frame the location where the load bearers ‘re going divide this measurement by 600mm this will offer you the same spacing for the struts. Next screw theses set up it’s easier to place a period of wood beneath the frame while doing this to have the edges to satisfy. Once this is done measure the cross member struts around three feet is around right for the spacing of such. They go vertically along those times frame stepping out then directly into accommodate screwing.
Positioning of those times, get those times into position using the help of the friend. Then start inside highest corner of those times and bang a piece of cut 4 x 2 (depending on the height of those times cut accordingly) into the ground having a large sledge hammer. Once done lift those times into position and screw together having a 4 inch screw. Now work along those times on the next horizontal corner lifts the corner therefore the frame is level and do the identical. Now work across the front have a very slight lean away in the house or make sure whichever way the boards are running tip those times therefore the water runs out with the surface. Then work your way across those times ensuring that any weak point is supported by banging a piece of four x 2 into the ground beneath it. Once this is done test the strength by walking across the struts showing any weak point don’t get worried excessive because decking boards will strengthen the decking once they are fixed on the frame.
Nowadays we cut and match the decking boards on the frame. Make sure each of the edges with the decking are cut square before cutting on the correct length. This will aid construction and overall Finnish with the decking project. Start having a full period of decking ensuring the finish meets the frame or cut the board on the nearest beam and fasten the board having a Paslode nail gun using 50mm nails or pilot and countersink holes and screw the boards screwing is best long lasting but nailing is faster and much easier. Work along those times spacing having a 5mm nail banged in a piece of four x 2, this will ensure that the gap remains the identical. Always remember to stagger the joints with the decking almost every other board therefore the joints blend into the decking. Once you decking boards are fitted then fit any surrounding decking boards on the edges to pay up any with the frame work and check for almost any boards who have splinters and sand these down if you can.