Ultrashield Outdoor Composite Deck Tiles By Newtechwood – Discussing begin first we need to measure the area could it be a turf or concrete base under the decking a turf base will must be dug off and membrane put under the decking you’ll be able to and really should put membrane under any decking project to halt any weeds penetrating through, where would be the damp course levels once we don’t want the deck over the damp course ideally the deck should be two bricks below the damp course. And will there be any drain access points under the decking as these need a unique decking drain cover. Always remember the decking boards go horizontal along your home. Always remember decking higher that 1.2m over walk out need planning permission
Now we’ve assessed these factors they will decide the height of the deck as well as any special requirements that must be incorporated in the decking project. Estimation of materials first look at the area in the decking i.e 4.8m x 4.8m = 23.04sq meters. Then employ this equation to calculate the decking boards needed 4800mm / 140mm (deck board width which can be 4.8m long) = 35 decking boards. Add a little for cuts and edges that must be filled in. Then calculate the load bearing supports (4 x 2 pressure treated CLS) 4800 / 600 = 8 This the amount of horizontal 4 x 2 pieces needed to the internal structure in the decking as well as the outside in the frame i.e. 4800 x 4 = 19.2m + (8 x 4800) = 58m of four years old x 2. Add some to the cross member struts and positioning pegs (banged and concreted if needed in the ground) about 3 or 4 4.8m lengths should suffice.
Setting up the frame this ought to be done near or as close on the position in the final deck. Start by cutting the ends in the required wood square this will help while using construction in the frame always cut the bits of wood exactly the same length because the frame should never be square if your wood is of various lengths. Then join the corners in the frame by piloting the holes to the 4 inch screws to be screwed into wood. Once this is accomplished you have to get the frame square, employing an engineers square install it in a single corner and move until square. Then screw a batten inside the corner to support the corner square do this for those corners. Then measure internally through the horizontal in the frame the place that the load bearers are getting divide this measurement by 600mm this can offer you an equal spacing to the struts. Next screw theses in place it can be easier to place a duration of wood under the frame while carrying this out to get the edges to meet. Once this is accomplished look at the cross member struts about three feet is all about right to the spacing of those. They go vertically along the deck frame stepping out then directly into accommodate screwing.
Placement of the deck, get the deck into position while using help of an friend. Then start inside the highest corner of the deck and bang a piece of cut 4 x 2 (depending about the height of the deck cut accordingly) in the ground with a large sledge hammer. Once done lift the deck into position and screw together with a 4 inch screw. Now work along the deck on the next horizontal corner lifts the corner so the frame is level and do exactly the same. Now work across the front have a slight lean away through the house or make certain whichever way the boards are running tip the deck so the water runs out in the surface. Then work your way across the deck making sure that any weak point is sustained by banging a piece of four years old x 2 in the ground beneath it. Once this is accomplished test the strength by walking across the struts to demonstrate any weak point no problem an excessive amount of because the decking boards will strengthen the decking when they are fixed on the frame.
Now we cut and fit in the decking boards on the frame. Make sure all the edges in the decking are cut square before cutting on the correct length. This will aid construction and overall Finnish in the decking project. Start with a full duration of decking making sure the finish meets the frame or cut the board on the nearest beam and fasten the board with a Paslode nail gun using 50mm nails or pilot and countersink holes and screw the boards screwing is better long-term but nailing is faster and easier. Work along the deck spacing with a 5mm nail banged right into a piece of four years old x 2, this can ensure how the gap remains exactly the same. Always remember to stagger the joints in the decking every other board so the joints blend in the decking. Once you decking boards are fitted then fit any surrounding decking boards on the edges to hide up any in the frame work and check for almost any boards who have splinters and sand these down if you’ll be able to.