Air King Quiet Zone 150 Cfm Ceiling Bathroom Exhaust Fan Ak150ls for measurements 1000 X 1000Bathroom Ceiling Exhaust Fans – The flush-style ceiling fan is mounted snugly alongside a set horizontal fairly low ceiling where it can be out of the way, and from which it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, with respect to the size of room being fitted, and can cost typically from $30 to $300. It generally has three fan motor speeds, which can be reversible. Except for the instruments and possible other parts needed for installing them, their self-assemble kits come with anything else. In many cases, the fan, which will have a unique lighting, will replace a ceiling permanent fixture.
Safety, The electricity has to be off to begin the location where the fan is usually to be installed. If the fan is replacing a permanent fixture, power down its fuse or circuit breaker as well as flipping its wall change to the off position. Stand on a sturdy wide-berth step stool or ladder during the installation; don’t lean or enter into a twisted position while there. Also, wear protective eyeglasses or goggles. Furthermore, if additional auxiliary household wiring should be used, get professional advice or help first. Tools needed, instructions (electrical) eyeglasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and further screws for securing the junction box, if necessary
Installation steps (reading the fan installation instructions thoroughly). 1. Remove the permanent fixture from the ceiling. With the electricity off, slowly get rid of the shade, bulbs, and fixture screws from the electrical junction box inside the ceiling. Let the skeleton fixture hang there. With the light tester, make sure the wire connections for this fixture are cold (the test light will remain off). Cut the wires, leaving 3-5″ of tail for connecting the crooks to the ceiling fan motor assembly. If the property is old, only two wires might exist, a black one plus a white one. Tip: also check the firmness in the electrical box inside the ceiling. If it can be not solidly coupled to the ceiling, add two extra screws to its top side, which might require drilling two holes inside the box for the kids. The ceiling fan is heavier compared to the permanent fixture. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends in the tailing wires inside the junction box cleanly, install the mounting bracket for the box with the two 5/32″ screw-bolts provided. Let the tailing wires hang outside in the bracket. 3. Hang the motor assembly from the bracket. Insert the topside motor-hanger into the centralized holder in the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly should really swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one for your motor plus a blue or off-color one for your lights being attached below it. Overlap the stripped ends of those two wires (motor and lights) together with the stripped end in the black ceiling wire inside the box, and twist connect them together with the wire nut provided. Connect the white assembly wire for the white ceiling wire exactly the same.
Then, to keep these connections from loosening whilst the fan is working, tape the wide lower ends of those nuts on their wires with electrical tape. Also, attach the green fan wire (ground wire from the bracket frame) for the electrical box if your box is additionally grounded having a third bare or green wire. Otherwise, if your electrical box in not grounded, ask a professional about it green wire connection. Some will say to get forced out be, i.e., do nothing with it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud for the far ends in the mounting bracket with the small screws provided. It covers/hides the perimeters in the motor as well as the wiring and ceiling box. 6. Assemble the fan blades (4 to 6) and mount them. After seeking the top or bottom reversible blade color scheme preferred, attach the blades on their end brackets with the screws and washers provided. Then mount the blades for the bottom side of fan motor with the bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed for the motor to keep them separate from the rest in the kit hardware.
Tip: to keep the motor from becoming too off-level during this step, install the blades one by one opposite together first of all. 7. Install the lighting assembly. Attach the fan’s lighting assembly for the small round central housing unit just underneath the fan blades using the quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders inside the order instructed. Note: a housing cap is provided if your lighting assembly isn’t wanted for any reason. 8. Test the fan and lights. After turning the electricity back on, flip the wall change to on. Set the pull-chain switches as desired. Often, the fan lighting is set ahead on with the wall switch, whilst the fan itself is controlled through the pull-chain switch only, initially set inside the off position. Note: The ceiling fan includes a reversible motor switch that permits the draft either to go upward or downward as preferred. For more information on ceiling fan installation, see the following sites.
