Home Decorators Collection Mercer 52 In Led Indoor Brushed Nickel inside sizing 1000 X 1000Remote Ceiling Fan – The flush-style ceiling fan is mounted snugly close to a set horizontal fairly low ceiling where it is off the beaten track, and from which it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, according to the size of room being fitted, and can cost typically from $30 to $300. It generally has three fan motor speeds, that are reversible. Except for the various tools and possible other areas essential for installing them, their self-assemble kits feature anything else. In many cases, the fan, that will have its lighting, will replace a ceiling permanent fixture.
Safety, The electricity have to be off once your there where the fan shall be installed. If the fan is replacing a permanent fixture, turn off its fuse or circuit breaker along with flipping its wall switch the signal from the off position. Stand on a sturdy wide-berth step stool or ladder through the installation; tend not to lean or get into a twisted position while there. Also, wear protective eye glasses or goggles. Furthermore, if additional auxiliary household wiring is necessary, get professional advice or help first. Tools needed, instructions (electrical) eye glasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and extra screws for securing the junction box, if needed
Installation steps (after reading the fan installation instructions thoroughly). 1. Remove the permanent fixture in the ceiling. With the electricity off, slowly eliminate the shade, bulbs, and fixture screws in the electrical junction box in the ceiling. Let the skeleton fixture hang there. With the light tester, make sure the wire connections for this fixture are cold (test light will remain off). Cut the wires, leaving 3-5″ of tail in order to connect the crooks to the ceiling fan motor assembly. If the property is old, only two wires might exist, a black one plus a white one. Tip: also confirm the firmness in the electrical box in the ceiling. If it is not solidly attached to the ceiling, add two extra screws to its top side, that might require drilling two holes in the box for the kids. The ceiling fan is heavier as opposed to permanent fixture. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends in the tailing wires in the junction box cleanly, install the mounting bracket towards the box while using two 5/32″ screw-bolts provided. Let the tailing wires hang outside in the bracket. 3. Hang the motor assembly in the bracket. Insert the topside motor-hanger in the centralized holder in the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly really should swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one for that motor plus a blue or off-color one for that lights being attached below it. Overlap the stripped ends of these two wires (motor and lights) together while using stripped end in the black ceiling wire in the box, and twist connect them together while using wire nut provided. Connect the white assembly wire towards the white ceiling wire exactly the same way.
Then, to maintain these connections from loosening as the fan is working, tape the wide lower ends of these nuts to their wires with electrical tape. Also, attach the green fan wire (ground wire in the bracket frame) towards the electrical box in the event the box is additionally grounded with a third bare or green wire. Otherwise, in the event the electrical box in not grounded, ask a professional concerning this green wire connection. Some will say to let it rest be, i.e., do nothing by it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud towards the far ends in the mounting bracket while using small screws provided. It covers/hides the perimeters in the motor as well as the wiring and ceiling box. 6. Assemble the fan blades (3 to 4) and mount them. After seeking the top or bottom reversible blade color scheme preferred, attach the blades to their end brackets while using screws and washers provided. Then mount the blades towards the bottom side of fan motor while using bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed towards the motor to maintain them separate in the rest in the kit hardware.
Tip: to maintain the motor from becoming too off-level during this step, install the blades individually opposite together to start with. 7. Install the lighting assembly. Attach the fan’s lighting assembly towards the small round central housing unit just beneath the fan blades via the quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders in the order instructed. Note: a housing cap is provided in the event the lighting assembly is just not wanted unconditionally. 8. Test the fan and lights. After turning the electricity back on, flip the wall switch the signal from on. Set the pull-chain switches as desired. Often, the fan lighting is set ahead on while using wall switch, as the fan itself is controlled with the pull-chain switch only, initially set in the off position. Note: The ceiling fan has a reversible motor switch that allows the draft either to go upward or downward as preferred. For more information on ceiling fan installation, begin to see the following sites.
